1_Disassembly/narration_transcript_disassembly.json

[
    {
        "category": "disassembly",
        "name": "User_1_411_1610_2_480.mp4",
        "transcript": " I'm going to disassemble this sub-assembly first I can just uncoil the wire and I need cross-head screwdrivers for this  Let's start from here.  So basically it is separate and as the upper upper screws, uh, bolts that I can also remove.  It's better to have a magnetic screwdriver  The third one The fourth one The fifth one  I still cannot move this so I'm guessing that  I also need to take off these sides perhaps.  slightly different and on these sides  it's difficult to maneuver this but this should be fine okay  you can see that this plate is almost off but this upper part this plate is now off and if i check the other side this sitting plate can also be taken off and can be opened up  these are rather identical taking off the next bolt  okay and the plates are sitting so that they sit flush with the the dampers so the plates can easily be taken off  Okay. And these on the side.  unscrewing this unscrewing this as well and unscrewing this  the lower panel is off this blade is still fixed here and also bolted on so it needs to be removed using a smaller screwdriver  it's still a bit fastened loosen this and loosen this and this part is off so  the plate would also now be detached here the upper plate is also detachable and also detached here and i see that this input panel has these electronic  circuits which can also be detached  okay from this end this has also been fessed and screwed in and this plate has also been screwed in so this plate central plate is holding the rest of the sub-assembly into place with this the disassembly process is now complete"
    },
    {
        "category": "disassembly",
        "name": "232cf338-98a7-4cdc-8683-417c0e2adf7a_480.mp4",
        "transcript": " So today we are going to disassemble this frame and remove this camera from the frame. So first we have to remove the camera. So we will remove this screw first.  And these two small screws.  We put them aside and then we have to assemble this frame. So first we have to remove this connector and remove this long road from the base.  So that's it. We removed the long rope from the base and next step we will remove this short rope from this long rope. So we have to remove this connector.  so the last part we have to remove this short roll so we can disassemble the base there is only one screw here so we remove the screws loose it so we can remove it  and finally we can remove this gap no it's a little tight so i think we finished disassemble this frame and remove the camera so yes"
    },
    {
        "category": "disassembly",
        "name": "User_1_412_2010_1_480.mp4",
        "transcript": " I'm going to disassemble this setup and the first thing that I'm going to do is just take out the zip dies and use this cutter to carefully cut the zips and same at this end  carefully okay and also this so this is now separate and the wooden plate can also be taken off so i'm going to do that  okay and also removing this screw so now this is the last one and with this i think the lower wooden plate is detached now i'm going to remove the  top screws on the top plate and I'm going to use a magnetic screwdriver to help with this  okay same here this one is hard to get out same here it's also harder to get this plate out let me see if i can lift it  i cannot so seems like they're not fitting into the thread very well okay  the only way to try is try and flip it and check if I can indeed somehow with that maneuvering get the screws out  seems to still be hard at this point so first I can start with the bottom plates and attach the plates two these are identical three  four okay these are placed here and this one two three four  okay so i'm not able to remove the bottom plate still so what i'm going to try is to somehow  try and push this out no it won't work so i'm going to proceed with the other plates the bottom plates or maybe even the side plate until then  key and on this end and here  here as well and i'm not sure if i also need to remove this but i'm going to try and also detach this  okay and the plate was held in place with this slot and with that i can remove the whole sub-assembly here i mean the plate at least on this side and i can see how it attaches onto the other things um  inspecting the sub-assembly on this side i see that i also have four screws to take care of and also these two slots so i'm going to first remove this  this screw seems to be different slightly than the rest and this  and to remove these i need a flathead screwdriver which is significantly smaller than the rest i don't see a flathead screwdriver here with me so i'm going to grab one  this should suffice but this is slightly damaged i think this would be ideal indeed this as well so i'm going to carry these  okay this works quite well just loosened and this side is also now being loosened  I'm going to place this flat and now I see that the plate is finally moving okay so  okay and the wire is now taken out of place and i can remove this plate as well okay and inspecting the sub assembly again you see that i can lift this plate up but not the rest because of this these two plates these two screws rather  um and if there's something i can do to accelerate the process okay so it seems like these two screws are not really suitable for this uh slot and they're causing a restriction okay and this is still not free but i'm going to maneuver this a bit  and now it is comfrey and this was also probably not fitting in at this place so i'm going to carefully the top plate here and position this so that i can remove the bottom plate as well  Okay. Okay.  and the bottom plate is free as well  just moving the card and other way around flipping it carefully and  this is the data cable of the hard disk and see that this is also a little rigid this is the power cable this is the data cable here okay and it was held in place with this button so this has been detached as well  and i'm going to remove the hard disk plate here this is identical  finally removing this okay so the hard disk is now separated as well  attached like this here on this location this is currently not in use so i don't need to disconnect this the disassembly process is now complete"
    },
    {
        "category": "disassembly",
        "name": "User_1_451_0502_1_480.mp4",
        "transcript": " I'm going to disassemble this Dell computer first I can lay down from this side because this is the door side that will open so carefully lay down and I'm going to open this hatch  and pull out the side carefully lay it down and i can see the different parts also listed here the gpus the cd drive the power unit the chassis of course the ram the fan there are multiple fans and also the different things here  So I can start by taking a closer look and I have some tools here available to me to disassemble and move some stuff around.  the first thing I'm going to do is take out this unit by opening this lock and this is internally connected here so if I try and pull this I see that this duct is also connected to this so maybe I cannot easily remove this that removing these wires or something  on this side there is no issue on this side there is the problem of this duct being held here see that there's a wire going here probably to the motherboard or to the fan  So I'm going to disconnect it using this wire.  disconnected so this unit is now disconnected let me see if i can remove this somehow and also disconnect the rest of the things remains to be checked properly  now this unit and there are multiple parts here try and remove this  He said it is held together by this hatch. It's not resting on anything here.  stuck here because of this thing and this also has come apart and if i wanted to fit this it would sit here i believe and fit in this fashion  it will sit using those flaps and it moves out the fans here and here the duct is also removed and this is the sink and here again we have different chips so i'm going to take apart these take these chips out  opening this lock but it also has to be opened from the other side it seems because it won't come off that easily so this chip here this chip here  I'm going to check if it fits ok and to open this hatch I'm going to have to pull again and this third chip is also removed what comes next is looking at these two GPUs and removing them but I need to be careful I'm going to take off this cable first black and white  remove this cable next remove this cable next these are fairly identical apart from  this here being let me check so this here misses one of the last slots because this is only 6 pins this has 8 pins and this is connected here  and there's also two screws that are connected on this side which won't allow the GPU to be taken out that easily so what I'm going to do is try and look at the slots and take out the bolts from here  the GPUs the lower GPU is here so I can take out this here it is really difficult to maneuver this perhaps I can use a smaller  It is still difficult to move it properly.  I think because of the angle at which this sits, it is very difficult for me to take off the GPUs easily from this side. So what I'm going to do is try and take off this slot somehow and maybe that helps me a little bit.  adjust this tool really quick okay and now it can work  I'll also take off this bolt and let me check if there is some give here. This fan unit can also be taken off here from this side.  Might be easier if I use a longer tool, like this.  and I'm going to take off this plug here and I can see that this is attached to the flap here so to remove this I'm gonna have to push this out and the fan unit is taken out  This power unit is no doubt connected very thoroughly the rest of the chassis. I can easily take it out. This is held here by this pin.  these screws are really small and it makes it difficult to reach from this side also tightly connected so i'm thinking of looking for alternative solution to this so that i can  move further so this unit is now connected here it's also connected here by these bolts which one move it's connected here by this  to this place also with bolts which will not move.  These are fit rather tightly If I take these bolts off I could maybe slide this part of the chassis out  I'm taking a look maybe it would be easier to take off these hard disk drives first these are data cables and these are the power cables and these are also attached here by this hinge so I'm going to press this and release the locks then I have to pull this out  that's the first hard disk second hard disk for this i will also take off the data cable and here the power cable  we'll pull that out we'll put this here we'll pull this out for the hard disk put this here so these slots are now empty  this pin so this sits here in this fashion so it is put in the right slots on this side and it is then slip down to place in the right position  Take this out In order to take out these hard drives GPUs They can be taken off from here by pressing on this which will take off the rest and  so now the only problem is these are these screws I believe this grill is also connected to this yes also held together by these small bolts  I search for a other slot that might fit. I don't think so. So the only option I have is look for a tool that would allow me to take this out. First, I can take these out anyway. And these are all the same, I think. So they can be used interchangeably.  So this will detach the power unit and it is also connected here with these adhesive. I think so it doesn't make much sense to remove this completely. I could do is look for a specialized tool that could fit here, perhaps.  So this is quite rigid unfortunately because I should have moved a little bit without this. Lay this down again carefully.  This is fit on this side so the entire slot might be Able to move back You can release this from here carefully This fits like this If I pull this here and I release this  can move back we have to be very careful so as not to damage the chips or the rest of the motherboard or anything else this here this here  The problem I'm facing is I need to lift this up, which these bolts are preventing in a way. And this is also these chips are also connected here, down here, which is also being prevented in a way. So I'm thinking of other solutions that can be used for this.  Perhaps what I can do is look for a smaller tool again.  I'm going to try again with these places here.  This fits, I think, but it is still incredibly tight.  so this won't allow movement because of a very rigid fit but i think this is the only other chance maybe  This is not good because I see that the thread is from the screwdriver is already getting eroded because of this. So it would rather erode the thread, the slot, rather than move and become loose, which is a very bad sign.  So as a last effort, what I can do is try and release this. I have pulled this out now.  and i have to pull this and i can release the gpu track on this whole system the screws and the bolts still won't come out but this is a small start i'm going to place it such that i don't damage the chips or anything so i think placing it in this fashion might be more prudent  now i'm going to place this back here and i can remove the cmos battery using the small slot  ok the cmos battery i can place here carefully this unit and i'm also going to take off the heatsink  so these bolts are also they also have springs carefully take off this and the last bolt is on the other side  also taking it off once again this one so heatsink is also now taken off and i can check the mechanism okay it should fit just insert it back it fits in these slots and this is the processor  these are the different slots remove this slot which will release the fan from the unit  Release this.  This data cable is also disconnected from the motherboard. And so is this. This can be... It's going to be pulling it out. Let me just quickly check. These are all data cables. Check and disconnect. Disconnecting data cable again.  This can be pulled out. This is also connected to this switch. Pulling this out. This is not a wire.  this can be pulled out by pressing on this lock and pulling it out i think uh let me inspect this one as well before okay this this this is connected here  I'm just going to pull it off here. And this bus connector, I think, is. I'm sure this can be pulled out readily. And what remains now is this.  These are the two things that remain, so I have to carefully pull this out This lock This is also pulled out  this i believe will stay in because this is just too sharp it's too rigid okay this pin has come off and this was connected on this side in the slot  theoretically the only thing that is holding this motherboard is these screws this this this this this so the heatsink the gp unit the ducts  the processing unit the ram chip unit the fan the hard disks have all been disconnected"
    },
    {
        "category": "disassembly",
        "name": "User_1_1910_aut_table_480.mp4",
        "transcript": " i'm going to disassemble this table and move this to the other room before i do this i need to check a few things so i need to cross the screwdrivers and the surface also appears to be a bit dirty i'll take this cleaning cloth i'll find  the cross head screwdrivers this should work otherwise this and I also need the carpet to  mount or to keep the table on the surface.  clean this I'm going to lay this on the ground so that I can put the table head here carefully lay down  and disinfect it and i think it might be actually easier if i just unscrewed from this perspective this is slightly easier  I'm going to transfer this to the appropriate location.  For transporting this, I can use the trolley. First I'll just clean this.  table replace here so I can bring this here and just leave it  carefully position this  and align this with the predefined slots here carefully and first try and go for the edges so that i can get things locked in place  aligning this it seems like this edge is slightly shorter so i'm going to align this  and try to see if i can align all of them from the beginning and i can see that the alignment is slightly better now but that just meant so  this end is also aligned i think okay  and this remaining bolt a screw rather will go here and then it will be held in place okay it's not aligning unfortunately I  Wonder if there's a slight misalignment elsewhere because I don't see that there are any available slots here either of the end. So this is, these two are not used at the moment as they should be.  based on this so what I can do is remove this and try to align it properly and make sure that all I'm not sure maybe eight or so are properly fixed and that there are  Matching slots also on the table on the desk.  Moving it and adjusting it. And I see two of them seem to align. Not really. Let me move this again.  I see now there are better alignments on each front so I think I made a mistake the first two times but now it should be more thorough.  We bring this back and the tools.  clean this and dust it up  And to make sure that the solution was accurate, I'm going to measure the horizontal level of where I'm placing this. OK. Pretty accurate.  Okay, so the processor is complete."
    },
    {
        "category": "disassembly",
        "name": "User_1_R_2501_Trolley_disassembly_480.mp4",
        "transcript": " I'm going to disassemble this trolley subassembly and take care of all the tools. First of all I have a lot of tools here and you can place them here to the side probably and  also these tools, this toolbox carefully placed to the side I'm going to open it to see if I need anything from here and at the moment I think I don't need anything to start with I have these instructions for the disassembly and see that the first thing I need to do is  put on the gloves and I have the allen keys here I need to remove the vertical bar at the very beginning and for that I think I will need one of the medium sized allen keys  I believe we'll try this to remove this vertical bar I need to loosen this and this and then probably also need to remove this this is too big for this side this is too large  Slowly turning it and I'm going to use the longer end so that I can maneuver this a little faster. I'm going to do the same for this end. Unscrew this, loosen this and then I can use this.  it's a good idea to try and take this bolt out first the bolt is out and before I take this out maybe because the bar is going to be slightly loose but I take this off very gently and I see these two guiding pins  so i'm going to put this here place this onto the side for the time being now need a smaller one for this side i want the same on this side i'm going to remove this bolt  and i think this has come off loose but i'm going to take this off and get this hinge off as well i think it's loose enough i'm going to take this off completely okay i'm going to place these two here to the side  We place this vertical bar here on the side. The next step in the instruction is the base plates and then the four wheels. These base plates will work with this, I believe. Yes. So loosening this.  with the shorter end and loosen this also loosen this  using this. Maybe I can just lift this up carefully. I'm going to sort the bolts so I can remember what goes where.  I'm going to do the same for this plate and the same for this. I believe they are all loose now so maybe I can lift this up as well. Okay. Same in this case. I can take off the bolts one by one.  and if i check i think they should be the same ones so they should be replaceable later and i'm going to carefully place this here onto the side i can now place this here below with me and  start to loosen the bolts of the third blade slowly this bolt already appears quite loose so maybe it isn't placed  the guiding pin properly this is this bolt is also now loose and this also appears loose to me lift this up okay soften the bolts  The next step is going to be, I believe, removing the four wheels and then also the individual parts of the frame. So I can probably start with  checking if i can remove this bar first because running the wheels without that is going to be slightly problematic looking at this i think this might this allen key might be the perfect fit i'm going to temporarily lock this so that doesn't move locked and  unfastened this same with this end  okay so this has come off completely so i'm going to take off this hinge corner connection and i'm going to place this here on the side and i think this pin was here  I can now flip this and also get the wheels out. I have to carefully place this down. Carefully. Lift up the locks.  how they can move and i think i need the biggest size of the allen key to be able to remove the wheels properly okay and carefully removing it  This wheel is out. The bolt is out as well. Soaring the parts. And remove this carefully. And rotating it anti-clockwise.  Okay, this part is also out. Now remove this. We need to align the key properly.  I believe it is in place. And rotating it anti-clockwise to unscrew or unfasten. Okay. I'm also going to remove this. And this bolt already appears a little damaged here, I think.  also pleasing it here this also appears quite tight  think this would fit properly this size it fits so i'm going to remove the holders that held the wheel here in position and i think it's tight enough that i can use the short end but with more torque i can  Loosen it already. It's also come off, so I want to remove the bolts. Place it here. Same on this end.  I'm removing this third one. I think the bolts will lose now. And taking out the bolts. I'm going to sort this here. And the last part.  the remaining step is to take out the frame and I'm going to inspect the individual corners and I can see that these are very similar to the one that I just took out from there so use the same sized allen key and start slowly  Loosening it. Perhaps I can make this stand. Lower condescend.  loosening this I'm going to put my allen key here and also try and loosen this at the same time so hopefully I can detach this bar completely take out this corner carefully with the bolts and the washers and it's the same for this end  And let's see if I can take off the whole thing. Yes. So this end is completely loose now. And I'm going to lay this down. Or maybe I can loosen this more readily from this angle.  that is at a risk of falling down so i'm going to lay this down and also loosen this  I'll do the same on this end and the bolt is quite loose here so I need to check if I can also just remove this  And this is also loose now. Looking at the steps. And I think the first thing I can do is I can sod them in a better manner. I'm going to remove these bolts.  and also place them here some of these bolts don't have a washer with them remove them  this is done and I can quickly clean the top part of the base plate also remove these bolts from their connectors  And I have to sort the tools back.  And the trolley has been disassembled and the individual bolts and their connectors are sorted separately so that someone else who is working on this can assemble them back together. So the assembly disassembly process is complete."
    },
    {
        "category": "disassembly",
        "name": "User_1_User_15_411_2910_1_480.mp4",
        "transcript": " so let's first we get some tools so you can empty that trolley and bring it to the other room and I can go here  Any other tools there?  Let me see if this dual fits. It's too large. Hello. Oh, sorry.  You can carry this to the other room.  Can maybe place this here and take the trolley back. No, I mean just here. It's out of the way. And position this here.  So we need a couple of different tools for this. Firstly, of course, the crosshead screwdrivers for the upper wooden table. And then we can first we can take this off and then we can disassemble the lower frame. So.  uh we could also flip it but the problem is that these things are stuck so we cannot flip it at the moment and also prepare the drilling machine too  So it is attached using the screws. So there's two on this side here and there's one somewhere in the middle. So if you come in the front, you should be able to see.  You can also use this if you want. I think there's a screw somewhere on the inside here. Yeah, but this side is not moving. And I cannot reach it without going in here and somehow reaching for the tool.  Let me check. OK. And the problem is that the height of the table is just too low. Can you pass me that too? Thanks.  Let's just do a temporary solution. Maybe we can put the trolley, put this under trolley and raise the height slightly. We cannot move it because if you check the wooden desk is in the way or maybe we can move the desk and then you can raise it. I think that's a slightly easier solution.  yeah i think that should be sufficient so let's check again okay now it is much easier to reach it  so now we can maybe remove this and place it here it would be at a risk of sliding i'm guessing so  okay so let's flip this then okay so then the instructions are need to have some gloves first of all  I think the other pair of gloves are in the other room where the safety kit is. You can go pick them up.  Let's use this if you want  i think we have another bit here and you need this bit so i'm guessing but you could do like the big screws okay let's do that  Or perhaps it's a bad idea to try this because some of them are too tight. So we have to start with the first loosen. We have to first loosen them, I think.  I think they are quite small anyway, so we don't need the drilling machine  Did you remove the lower ones already? Okay. Just place it here.  so i think these have the same size i think this was placed here to guide the crank so i think we can unscrew first the outer ones and then the inner ones you can find a drill bit  This should work.  Okay.  This end seems to be extremely tightly fixed. You have to go the other direction. Like this way. Am I screwing it accidentally? You're tightening it.  I can take the longer one.  I can separate them.  so all the parts have been separated and yeah then we can just put the tools back and finish the process  And the other drilling machine is here.  Can you put this in? And I'll take the trolley out.  Okay, the process is complete."
    },
    {
        "category": "disassembly",
        "name": "User_1_User_15_0602_Disassembly_480.mp4",
        "transcript": " we're going to disassemble this workstation computer first we have the steps here but I think we can wear gloves because some parts may be sharp now for disassembling it we need to put it down so we can just do that carefully  and the first step is to open the hatch and remove the door yeah you pull it out and release it and same from this side yeah just place it here  we have this reference image to compare and identify different parts so obviously this is the chip rack here the GPUs the hard disks the duct here there's a battery here down here and there are some parts underneath the duct which we cannot see at the moment so we'll remove all of them step by step  so we've completed the first step first two steps pretty much so the next one is to remove the chip rack which is this one so to remove this you see this sort of lock you open it so pull it and you'll open it this this one yeah just pull it and then it should be able to slide out yeah so let's just place it somewhere on the side  yes so we see that this is done the next thing is going to remove the duct but I think the duct is sort of locked in place on this fan here so you need to take it out from here and pull it a little bit so that it releases yeah you'll have to maneuver it a little bit  And yep.  We also remove the duct and we see that the parts that were underneath are now visible. I think the next easiest thing that we can do is remove these three RAM chips. You'll need to release the latch from both sides. Oh no, you can do it at different times, but you'll need to do it on both sides.  I think it might be easy now to remove this fan because this is the  uh fan one fan one is this so we need to so i think this is attached first of all here with this cable so you need to plug it out i think it might be held in place with this a small latch yeah it's removed and on this side i think it is attached with frames so i don't think yeah this might be the correct  I'm going to empty this Use it Yes Let's put all the bolts in this Okay, so  The next thing which is slightly more challenging"
    },
    {
        "category": "disassembly",
        "name": "User_1_User_16_411_2210_1_480.mp4",
        "transcript": " Okay.  okay we can maybe move this a little bit further okay um okay i'm gonna keep this in there must be two sets of keys right so you take one and i'll take one small okay  we can put it here these ones  We'll be able to lift it now. These. So these. And I'm not sure. The other ones as well.  It's too large. OK.  Let's keep them here for the time being. Then we need to take out these from the drilling machine. Yeah.  OK.  Okay. Hold it. I'll try and unscrew this. Sorry to low.  We should be able to pull them now. This is locked here.  These legs. I know what fits. This fits.  I don't think that will fit.  Where are these four from? Just keep them. From here. From the top. Okay. Cool. So let's store them separately. Okay. Okay. And then in the end, I'm going to take out the machine.  Okay."
    },
    {
        "category": "disassembly",
        "name": "User_1_User_16_411_3010_1_480.mp4",
        "transcript": " Stable top  These? Oh yeah.  Okay, that fits.  Yeah.  Still...  There's also a fourth one or? Okay.  through the sidebar hmm  Okay. And also this. Hmm.  the bolts are all here put the tools back"
    },
    {
        "category": "disassembly",
        "name": "User_1_User_16_451_0701_1_480.mp4",
        "transcript": " Yep.  This is far too big.  yeah okay let's sort this along with that so with this one works let's check  The floor? No, after we finish the disassembling. Let's remove this. It's too large.  OK, thanks.  let's flip this and let's remove the wheels rotate it  Yeah.  okay now let's sort the things um this is here this is here um the tools  Now I can clean that.  Okay, so the process is complete."
    },
    {
        "category": "disassembly",
        "name": "User_1_User_17_411_2210_1_480.mp4",
        "transcript": " so we can clear and clear the stable first  all right um we need to get rid of the tape so oh yeah okay okay so let's lay down the  thing where we can actually or else we can pull this out and give this to the side maybe just remove this  So let's just lay it here. For the rest of the assembly. Bring it here. And the first thing that we're going to start off with is with these handles.  Allen keys. Try this. It's too large. Too small. Yeah.  Okay.  I think it should be let's check if you lose this then you can take this apart but you cannot take this so let's maybe try and start here  to see if you can just take this rod off or something.  stick it off yeah yeah so let's take this off come to this side yep  pretty long yeah the screws are identical we can leave them here  okay i think uh we can just do this standing i don't think we need to flip it and then sit down for this so i think we can grab these tools  Okay.  Thank you.  I'm just seeing to lose both things at once and then maybe  to set you mean okay i think we'll need to work on that together later if it is  very challenging to hold then we can just flip it and lay it on its back just hold the two legs just lay it on the ground yeah or maybe even like this yeah  okay i understand the mechanism here okay  I think if it's loose enough we can just hold this  Okay, so let's make sure that we have sorted the different bowls and different parts that belong together. So these bowls are different with washers. These are here for the legs. The table is there and these are for the hangers. Okay, all right.  so the disassembly is complete right i don't think we left anything here maybe these leg caps uh i don't know if they are detachable but they are just for adjustment i think i don't think they're detached  So the disassembly process is now complete."
    },
    {
        "category": "disassembly",
        "name": "User_2_410_0411_1_480.mp4",
        "transcript": ""
    },
    {
        "category": "disassembly",
        "name": "User_2_410_2110_1_480.mp4",
        "transcript": " To start the disassembling process I will start with removing the wooden plate on the bottom of the embedding computing unit. I'm flipping this over to have a look at the wooden plate. Okay, but it seems like I have to screw it from the top.  with the cross-headed screwdriver and this is one but i can't find the right angle with this one because it's too big so that's why i'm gonna use the smaller one removing the screw for the wooden plate and set it aside  Removing the next screw. I'm turning it over to remove the other screws on the other side. This is number one and the last one. Like this. Put the screws over here.  Now I can remove the wooden plate and set this aside. The next step is to remove the bottom connector plates. The connector plates are those metal pieces here on the side which were attached to the wooden plate.  In order to remove the screws there, I have to flip it over. Use my cross-headed screwdriver for the 8 screws.  so now i successfully removed one of the bottom connector plates set it aside and finish up removing the other plate so  Now I can set all the removed screws. Put them here. The connector plates are here. So this is done. The next step is removing the  um the side plates i'm going to flip the pc unit over again and to remove the side plates i will need a cross-headed screwdriver too and start by removing those here  Okay, so I try to remember that the bigger screw here with the bigger head, the rounded head, was in the top left corner. Now I should be able to remove the side plate. It's kind of still stuck.  So this is a bit... It's not tight. I'm just gonna screw it tight.  um oh yeah there seems to be a problem with the side plate it's not it's not coming off maybe i have to yeah i have to remove the um the green power connection first and therefore i need to use a flat headed screwdriver  I'm rotating counterclockwise to remove this.  so I could remove the power cable I'm just gonna leave it here so it doesn't fall off the table and now I should be able to remove this plate and leave it here and the screws that I used will stay here  so that i don't forget that these were the screws for the side plate now i'll continue with the other side plate there i will need a cross-headed screwdriver too just remove the four screws for the side plate  now i can remove this plate too but it seems like there's no real grip okay so now i successfully removed the second side plate um yeah the next step is removing the bottom plate  um and this is here there are six screws for that i can use the cross-headed screwdriver untighten and remove all of them  Now that I removed all the screws I can take off the bottom plate and I will just leave it here and place the screws for the bottom plate next to it. Next thing I can do is removing the top plate. It also looks like  case for the cross-headed screwdriver just remove all of them so i can't take it out with my hand maybe i can use the magnetic the magnet of the screwdriver like this to remove all the screws  okay so now i successfully removed the top plate too we'll put the screws next to it so i know that these were the screws of the top plate now i can remove so this was the top and the ram chip is on the  on the upper side below the plate and so this was the plate and below it is the ram and it looks like this is removable  so it looks like I can click off those holders and take off the RAM chip I'm gonna leave it here put those here back inside and  The hard disk power cable was here. So I think I can remove this by unscrewing probably. Hard disk power cable. It's on the lower side.  it's on the lower side which is here the hard disk power cable probably yeah this was already detached and i can detach this cable too and yeah so  Yeah, this is probably the data cable and this is the power cable. Both are detached now. And now I can unscrew and detach the whole hard disk. I will also use a cross-headed screwdriver for this. And it looks like there are four screws that are holding on to the hard drive.  these are four screws for for the hard disk yeah now I remove this and with that I successfully disassembled the embedded computing unit and can now inspect the inner  than a part of the PC yeah so"
    },
    {
        "category": "disassembly",
        "name": "User_2_411_2410_1_480.mp4",
        "transcript": " To disassemble the lamp I'm going to unplug it first and remove the light bulb and set it aside. Then I will unscrew the clamp mechanism to detach the lamp from the table.  like this and remove the clamp and also set it aside now I can place the lamp on my workplace and start with removing the lamp head therefore I'm gonna unscrew those smaller screws  They are tightened by nuts from the inside. I'm going to try holding onto them and then unscrewing. And then removing the screw like this. Like this.  i'm gonna put the screw in the nut to the side and then i'm gonna do the same thing with the screw  So now the lamp head is removed. Now what I can do is... It's removing the upper hinge for the head.  And remove the screws here.  so these are for the hinges these are for the head and i'm gonna place the screws and nuts for the hinges next to it i have to hold tight hold the nut fast so that i can unscrew this screw the nut could be removed  And like that I removed the two nuts and the two screws for the hinge. And now this one can be removed by hand. Like this. And there was a nut in here. I want to place it in here to not mix it up with other things.  I can remove plates.  Like this. Like this. Okay.  so this was the first step now i can do the same thing with the middle hinge but i start off by unhooking the springs here here put them aside  And I can unscrew the hooks here for the spring.  then i continue with the middle hinge and i can unscrew the three bolts here probably some nuts on the lower side i'm gonna just hold on to them and then unscrew the respective screw  other things for the uh middle hinge three nuts three screws and the um trapeze plates and place them here um and the bar the removable uh movable bar one then  what I'm gonna do is continue with the lower hinge I'm gonna unhook the springs again like this unscrew and unscrew the hook  so these are not removable so i'm gonna leave them but um i can uh yeah unscrew those bolts this one is just the hand twist also with the nut inside  second removable bar  then the hinge place here with the hand twist with the nut and the two bolts  Okay, so now I disassembled the lamp and set the objects and bolts and springs and hooks and plates in one pile so that it's easy to reassemble the lamp."
    },
    {
        "category": "disassembly",
        "name": "User_2_411_3009_1_480.mp4",
        "transcript": " So I will now disassemble this camera stand assembly for computer vision. For that I have to take it out and place it on my working station over there. Before that I'm turning on the lights.  yes I will lift this now onto my table like this for disassembling I need to remove those covers I will use  a screwdriver like that like this to lever to use it as a lever to get those covers out then i will be needing some allen keys or one specific one which is located in this room and i'll get it from here  yeah here are different kinds of allen keys that i will be using i go back to my working room close the door and then i can start disassembling and first i'm gonna remove the covers  I use my screwdriver as a lever  to be able to have more space on my table I'm cleaning this workspace up a bit just like that just put things that are not needed to the back of the table so I have more space in the front  I continue removing the covers here and here two more and that's the last one  place the covers here so I don't mix it up with other components of the assembly and then I can start disassembling the metal bars  I'm trying out the allen keys and see which one will fit. This one does. So I will be using this allen key to remove those screws.  yeah instead of doing the bars first i will start with removing the four screws for the plate this one is already loose  i just removed three screws and here's the last one for the for the plate the plastic plate and now i can remove this i place it here and lean it against the wall  Then what I can do is remove this metal bar and I start with removing each of the connecting corner pieces which are assembled with two screws each.  I'm going to put in the shorter side so I can apply a bit more force I have to do it counterclockwise to remove the screws  so this screw also has this metal square piece to lift it a bit and to not damage the metal below place them here those are the corner pieces  The connecting pieces here I can just leave inside. They offer a hole for the screw to fit in. I have to hold this metal bar now because if I remove this screw it is detached from the main assembly.  I can remove the screw and place it here. And I can remove the wire screw to get rid of the corner piece here.  Just like that.  There was a little screw here. I remove it. Okay.  so I can now detach the little bar from the bigger corner piece  ok so this one is a bit hard to remove I need all fours here and there is not enough space to use the short side  Use the long side, can't apply enough force. That's why I'm just gonna leave it like that. Alright, so I will be doing the same thing for this metal bar.  I will loosen the two screws of this corner piece. And so I can remove the corner piece and place the two screws to the other screws, which are all the same. Like that.  hold on to the metal bar because when i remove this screw again then it is detached from the main assembly and then i can remove the screw here  Okay, what I can do now is again remove the two screws of this corner piece to detach the upper part from the lower bar.  There was another loose screw, and this screw I just removed. And what is missing is the slightly darker screw here, which is still the same kind. You can place it to the other screws, and the corner piece comes to the other corner pieces.  There's this connecting part that was also the same as with the other bar. If I can, I will remove this one by hand.  If not, I'm gonna leave it like it was with a bar before. It seems like. Okay. I can remove it.  so i just remove the bar remove the bigger corner piece of this bar and i can place it here and what is left is removing the small one which is a bit hard but  Now it is loose and I'm gonna remove the screw. So that I can detach the corner piece. Like that. What I'm gonna do next is...  What I'm gonna do next is removing the bigger bar. And here's a corner piece that I can remove. So those two components are holding onto the longer bar and that's why I removed this first.  this one is also a bit loose already and on the side there are also two screws yeah like that  So I can place all the square parts in one place and the screws in another place.  here's some connecting pieces in place here and now I'm going to be able to remove the last component to remove the whole bar  okay so this last screw is holding on to the bar and the screw here is i can unscrew this to detach the corner component just like that okay  I'm going to place it here. And the last thing I will do is remove the handle here and the short bar from the long bar. Here's another cover piece that I will remove with the screwdriver I used before.  I'm gonna place it next to the other cover parts. When I remove this screw I can detach the short bar with the corner piece.  And I remove this screw to detach the corner piece.  and for the handle I have to use a slightly bigger allen key which was also like there I can unscrew this long screw and so that I could remove the handle  After disassembling I can inspect my bars. The last step here is cleaning up a working space.  And that was the disassembly of this computer vision stand assembly."
    },
    {
        "category": "disassembly",
        "name": "User_2_451_0602_1_480.mp4",
        "transcript": " okay to start the disassembly of the workstation computer I will start with putting on working gloves to prevent any possible injuries I need to open the hatch first by pulling this lever okay  I need to inspect the computer first and then I will start with removing the chip rack and one of the fans. This is the chip rack and here's the fan I'm gonna remove. Pull this out like this. And I just place it on the side here.  Then I will remove the duct which is here.  Now to remove fan 1, I need to detach the frame first. That's here. Detaching the frame, therefore I will need a cross-sided screwdriver. Just loosening the bolts here.  I'll remove the cable from the motherboard here too. Like this. And place it here with the bolts next to it. Then I'll remove the bolts which are attached to the GPU frame.  the GPUs are here and I will need to remove the whole frame so I'm gonna open up all these bolts here  Okay now I think I removed all the bolts. But for some reason it's still not getting loose.  I think it should be removable now.  try to figure out what needs to be loosened  I think here on the bottom it's still not loose.  of the motherboards and the GPUs. Now removing the cables. And then I can place this here together with the bolts. Okay, next step.  detach the cables attached to the HDDs and remove the HDDs these are on top here take the cables out  Okay, now the HEDs are moved. Next step are the RAM chips, which are attached to the motherboards. These are the RAM chips. Just open up those."
    },
    {
        "category": "disassembly",
        "name": "User_2_451_0602_1_1_480.mp4",
        "transcript": " Okay, I'll continue with the task. The next step is removing the heat sink. I already opened these screws up. The others are a bit hard to reach. So I'm going to try again.  A super timed pair of pants.  again with this one too small okay there's no other screwdriver available this one is a bit too big to fit in this small space here  I'm just gonna try again, if not then I'm gonna leave.  i don't know why but it doesn't move so i'm gonna leave it next step is removing the cmos battery done then the frame holding the cpu the cpu  That's underneath the heat sink I think. Therefore I also cannot reach this one. What I can try is to reattach those and try to reach the others first.  The motherboard. Here.  and the parts are already sorted so now i'm finished i'll take off my gloves"
    },
    {
        "category": "disassembly",
        "name": "User_2_User_14_407_2210_1_480.mp4",
        "transcript": " Alright, then let's disassemble the adjustable table here. Just put on your gloves. So...  So we just start by setting the height to the... Oh yeah. Just setting it to the lowest setting with the crane. Then we can just start by unscrewing the three bolts on each side to take off the plate, the lower plate. Maybe you can start on your side.  and i can also remove the crank here and i will do the bigger bolts here  And maybe you can put the bolts here. But later, you can do it afterwards. Yeah, you can do it here too. I will do the bigger ones here.  So we can set the plate here aside. And maybe put the bolts over here. Are there any left here?  Okay. Um...  Let's take off the cover. Oh wait, I forgot one. Can you hold on to the leg?  okay so so now we can remove the bolts that are holding on to the the rod in the middle yeah like this is the rod and there are like two screws that are holding on to this  Here? I think here. One here and one here. These two? But it says allen keys. Only those are allen keys here.  Okay, let's try out this first.  It's not moving, right?  oh just pull it out like that now we just pulled out the middle piece of the rod  hmm no I think it says here the connecting rod from the inside so this is the connecting rod I think so remove this and now we can use the electric drilling machine to for the for these but we need to can you give me the toolbox there the bits  So we need a bit that fits here. I think this is good. Maybe this one? Yeah. Can you... Yeah. Can you plug this in?  Maybe plug in the power cable first. Yeah, there.  Hold this. Mm-hmm.  Now, what can we do? OK, this is too.  okay I mean it just says like separate the two legs and what we can do is like in this picture the legs are already separated yeah let's just place it like this  Put this on the side. Okay, so we can look at the bottom and remove those screws here. Okay, so I think... Yeah, you can do it here.  This one's too big. It's not? Okay, wait, let me try it.  You can just untighten them. Thanks. So these are the screws.  For the outside of the legs. I can do it.  Can you maybe sort the bolts?  wear your four screws here okay then just leave it like this hmm  Yeah, then I think we're finished with the disassembling. Let's just clean up the tools a bit. I can do the drilling machine. Can you sort those in? The allen keys and just put it on the table.  I think the blue one was in here. Here are the colored ones.  um yeah okay um stop the recording now okay just put off take off your gloves"
    },
    {
        "category": "disassembly",
        "name": "User_2_User_14_411_2310_1_480.mp4",
        "transcript": " okay first uh let's put on the working gloves and i have to watch out for my white shirt um yeah maybe yeah let's just start with removing the the gray bolts  And I can assemble the drilling machine.  The other screws are on the ground. So.  yeah maybe you can remove the those screws and these and i can do the outside ones  yeah oh i think this is the other way around dark side yeah okay then i think we can remove the middle rod  Put this there. And just flip the legs like this. Yep, just remove the screws.  Mm-hmm.  Okay, nice.  Okay. No, we are finished, but we can disassemble the, just clean up a bit and disassemble the drill machine. There, this is toolbox.  Okay."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_15_411_3010_1_480.mp4",
        "transcript": " So first we can detach the plate. Maybe on this side. And then I think we can throw away the tape.  okay and then those corner pieces and the other side okay let me take this one and I can  Yeah, I think we have to remove the whole thing to detach the rods. Yeah, I mean those bars we also have to separate, I think. No, this is just like, it's removable like this. Oh, the screw, I mean, yeah, just the whole, yeah.  Can you hold it? Yeah, thank you. Hold all of it? Okay. I mean, I can take this and put it on the ground. Oh yeah, I think it's easier. Thanks.  okay now the side rods it's the same size  Bye.  I think that's it."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_15_451_1601_1_480.mp4",
        "transcript": " Okay.  Oh, this is attached. Is that the only one in that size? These should be the same size as them. I mean an allen key.  This was a bigger one. I can do the wheels first.  we have to flip it though to remove the wheels or you think we can just like remove this or like remove the whole thing yeah then i think we have to flip it a toolbox about this one oh okay  Oh, what are you doing? Oh, I mean, it's the same result. Oh, I can, I mean, now I already did it, but I can also remove those now. Attach the four wheels, the wheels.  Reunions don't need to be disassembled further. I think this is better.  Oh no, I took this one.  That's it. Okay."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_16_410_1010_1_480.mp4",
        "transcript": " okay so what we want to do is fix this assembly stand and  this part of the assembly is rotating and we want to remove it and see if we can fix it but first we have to disassemble it and we can just start with the allen keys  Yeah, the bigger one and then remove the corner piece here to take this off first. Yeah, let's maybe start with this here. Oh yeah, if this is in the way, we can also remove this first.  Okay. Yep. Just leave it on this side. And then... Okay. I'm gonna leave them here too. Okay. Then we can maybe stop with removing those.  okay um did you also remove the one here so we can take off the bar maybe oh yeah we can just slide it off like this also you have it okay i can put it here  i can place that here it's a screw for that yeah just okay um yeah then maybe this here yeah we can remove the bar first just like the other one  Okay.  Okay, it's still not removable, right? Okay, let's maybe just remove the bar. I can remove the screw here. Oops.  I'm just putting the screws back in so we don't forget.  okay um yeah and the last one maybe so yeah let's just take the smaller keys and  And then there's one down there. It's still not movable.  so i can't like move it up or push it down or like maybe slide it off okay um then how can we remove this now can this push up no right  It's super tight.  it's not removable it's a little little thing maybe that's fine yeah need a smaller key for that too small too small yeah  we can look in the room next door  I don't see one that's small enough. This could work.  the same one it's a bit smaller but i think it's too small you can just try it out okay yeah let's just try those three  yeah okay okay perfect then maybe try the one uh here one beneath yeah perfect okay no problem okay so there's it's like they're in between on both sides  Sorry. Yeah. Counterclockwise.  not quite i think just remove it completely  I know you just leave it in, because this one you also just left in. Oh yeah, there's also one beneath. Maybe you can leave this just in here. Oh yeah.  so the three can you get take the key and maybe like try to get this small thing there you can just slide off the bar  or maybe okay maybe you can hold this and i uh take off the covers and then we can just slide off the whole thing on the top oh yeah okay okay  okay so now we can remove this thing finally but first yeah let's take off the covers of the bars here  Yeah, okay. Slide in there. Something. Yeah.  oh i think here's a you don't want it to break yeah this would work because the screws are only in this track here okay so now the way is free to slide it off  It's stuck here. Okay. Yeah, you have it? Perfect. Um...  okay so now what we want to do is add one more of this piece on every side so we have like two fixing parts of this assembly so it won't rotate anymore  okay perfect yeah okay it's good and i think if you want to put one screw inside we have to remove one bar oh yeah and then slide it from or maybe we can even i don't know if it fits i wanted to take those screws right i'm sorry  okay what about the smaller screw here okay but this one just slides off now another one  this one is good and this one is also long maybe we need a bit longer just take all of them  mm-hmm yeah you have it okay so now just take this and this one screw oh so this one is a bigger one i only have um yeah maybe i need the smaller screw  but we we will need those to like reassemble ours again right so i'm just gonna maybe take a smaller screw  Yeah. Just slide it on. Okay. Yeah, we can just try.  I think, I don't know, mine is maybe a bit too long, my screw. So it won't fit in there. You can try. I need another screw maybe.  Okay let's see. I think it could work out.  Mhm. Okay, then reassemble the bar. Yep. It's yours in.  notice no i'm gonna fix this like fixated okay make it tight okay now we can slide it on and then we have to align the two things with the tracks here  Maybe let's do one side first. And we'll just hold it and you slide it on. This part was too much. Can you try if it can be fixed? It's kind of stuck. And just screw it off a bit. Then we can put it inside. Can you do it by hand?  Try to hold the screw inside. Yeah, like this? Okay. Okay, and the other one?  Okay. Can you hold it?  Can you lift your side like a little bit maybe? Some trouble like to line it here.  I think I have to screw off a bit too. It's not too long like the space in between is too little. What do you mean?  Oh, okay. Maybe let's do this side first because this side is a bit harder. Yeah? Okay.  Is it in?  Should we screw it off? Let me think, do we have some another way to do this? So, was the problem that this was too short? Because, I mean, there has to be space for the metal here, like this, to slide in. It's not too short, because this one is the original one. And if this fits, that one is... Okay, so let's maybe just try again.  I just have to... Oh, wait. Yeah. I can see... Can I use hammer?  Yeah, it goes in, right? Maybe, okay, can you hold this real quick and I align this and then we can hammer the whole thing. Okay, here it's in. So maybe you can just like...  Thank you.  It's a bit too tight, right? I think we need to make a bit more... Can you close the door? I think I can just screw this off a bit more, maybe.  take the scissor and hold this one yeah no problem I can hold the scissor  a little bit i think this is even enough yeah so i think this should work now just have to watch out to not let's try first like this okay okay  Okay, I'm aligning mine. Does it fit on your side now? Tell me if I have to lift or something.  Okay, let's do your side first. We have to draw this way. It's in how many millimeters from here. But it doesn't fit like this.  Okay, so just leave it like that and I align my side. Okay, mine's in. And yours too, right? Yeah. Kinda. Kinda. I think we'll have to move a little bit. Like that. To the right.  I think we'll have to move it a little bit. How? Yeah. Okay, so yeah, this.  Yep. And here it's still in. Okay.  Okay. Hmm.  I think also like I think this is like too much on this side I think more the problem was that there was like they were like not the same length um  doesn't really it is the original one right yeah but now they are like kind of the same right  Let me make a curve Okay  Yeah, go inside directly. Yeah, mine is also in. Go inside, right? Oh, wait. Yeah. I'll just push it down. Is yours in?  Mine is like a bit tight again. Okay, yeah. Yeah. Mm-hmm.  okay no wait i have to sorry now  oh my screw's off yeah maybe what we also need is like a longer screw that fits in this one  these are all too big okay what we can do is um i mean the thing uh will stop rotating if we have like um only two on one side right yeah so um maybe let's just do this  Let's try if this slide down will be better or not. Okay. It seems not. I cannot see. Yeah, I think it's a bit harder. Yeah, let's just do the other one again.  Okay, yours then.  I have to screw it off a bit. It's too...  I can lift this through there.  But I'm seeing now that we might have to... No, we can put it on the upper side, right? The rotating thing? Yeah, we can level it, put it in here, and another thing goes down.  hmm yeah but i mean the rotating thing was in the middle here must be in the middle yeah it must be yeah okay i mean no problem we can just do it again okay just hold it and taking let me see how how how  Okay. Yours in? No, not yet. I will work in here. Okay.  yep okay just leave it here first yeah that's possible but now it cannot rotate anymore okay  Yeah, but just leave it like that. And I think we can stop the recording and do the reassemble."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_16_411_2510_1_480.mp4",
        "transcript": " Yeah, maybe let's clean up the space first.  okay okay then let's detach the plate I think it was glued here or taped we can just like pull it off okay watch out not that the plate gets scratched or something  Oh, you alright? Okay.  huh this one's too small are they different this is a 12 you have 14. okay that's weird okay now it fits okay i don't know why  yeah okay okay we could have just hold on to it maybe let's put it on the table yeah like hooks  yeah maybe i can see if i  oh this one is the same this one is a 13 13 or 12. yeah thanks  Okay, then... I think it works like that. No, just this screw with Ellen. Dangerous.  It's the same. They're pretty long. Mm-hmm.  Okay, so I think that's it."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_16_451_0602_1_480.mp4",
        "transcript": " And I think first thing would be just putting up some gloves to prevent some injuries. And let me just lay it down like on its side.  Just like this, I would say. Because you have to open this one. It's heavy. Let's take the whole thing. On the top first. Just click it open.  So we can start with a chip rack and here's like a lever you can pull. Just pull it to the side like this and then pull it out.  Then the duct, just this cover thing. Just pull it, it clicks. Then the fan here. Then you just need to...  And then the cable here. I think there might be a button here. Then after the fan we can do the CPU frame.  GPU frame. And then we have to take out the whole thing. So like around here, just remove all the bolts. So like these, these, these. Just take the whole thing out.  Okay, and maybe detach all the cables. Those two. I think that's it. And then you just pull it out in this direction. I think you need to lift it a bit because the chip here is still inside. Lift this and then pull it out. It's also locked here.  Oh, OK. OK, nice. GPU and then the HDDs here, those just detach all the cables.  you know just leave the cables and then just use those levers to pull out the hgds sometimes it's a bit stuck you have to like pull both like equally yeah  and next the three ram chips then this heatsink because underneath is the cpu just like those four screws here  And now I think we need the other screwdriver, this one with a star shaped head. For those four screws. That's the frame for the CPU.  yeah and now you remove the cpu unit here yeah just lift it up it's like a small square there  Then the CMOS battery, the small round battery. Oh, I don't think. I think you can just like, or maybe use the screwdriver to just press this button. Yeah, the golden. And then remove the cables from it. Maybe you can use the big ones, but those can all be removed.  I mean, just leave the big ones. Yeah, and then...  I think you can leave this, but here the orange one maybe. And then the long black one here. Okay, I think that's enough. And yeah, and then leave all the parts on the side and then that's the disassembly. And this process is done, can remove the gloves."
    },
    {
        "category": "disassembly",
        "name": "User_2_User_17_412_1510_1_480.mp4",
        "transcript": " okay so in order to disassemble this table we need to remove those screws here and the first thing we can do is flip it so we have better view and like better angle to unscrew them so we can use this yeah thank you and just place it on the ground  Yeah, I think this is enough. Like this. Maybe you can also turn on the light for a better view. Okay. Then we flip it now. Okay. And three, two, one. Okay. You have it? Yeah. Okay. Yeah.  not so heavy okay so maybe you can hold it and i unscrew it yeah it's not heavy so we can both okay yeah but i think here's only one screwdriver yeah there's one okay or maybe we can look in the other room for another one and here's also  because we need the cross. Yeah. Just unscrewing them.  and that's the last one so i think now we can take off the the whole plate  so um yeah maybe you can can you put them in your pockets or your pocket or if you don't have a pocket i also have yeah okay so now we want to um transport both pieces to the conference room and um and the car we can like do later uh is it heavy how heavy is it  It's okay? If not, we can take the trolley. Okay, then I will take the plate. And then we can bring it to the conference room. Yeah, just take it here.  Just put it in your pocket. Yeah, yeah. Just put it in your pocket. Yeah, it's here.  yeah you can just place it in the room somewhere okay it's also good because here we don't need the cloth because we have carpet in here so the plate won't get damaged okay then we just place it on top again  Try to align it with the holes.  Yeah, I mean, here is a line, but I don't see any here.  Okay, on this side it's aligned. But here it's not. Here, here, here. Here, here. Yeah, I think that's it. Okay. Then...  I just tighten them pretty lightly so we can still move the plate.  this okay i think we will need like maybe the um the electric yeah um drill machine from next door because this one rotates  maybe you can try but it rotates together with the yeah yeah at the last four yeah so yeah maybe we can get the electric drill machine and bring back this  I can close the door here first and then we can come here later I will bring back this screwdriver put it in the drawer and then I can take out the the electric drill machine  and um i can take this too to assemble it and put the drilling bit inside i just have to check if they have if here's a cross a bit yeah here are several so one of them might work  I will take those two components and bring them to the conference room. Hello? Yeah.  Can you plug this in? Yeah, it works. But first we also need to assemble it. Does this work? Yeah. Okay, then we can take this.  press this button to open it up insert the drill bit and press this button to tighten it hold on to the black part until it's tight okay  okay and we can try okay it's tight so yeah let's flip the table yep and now we can place it maybe over here  But I think what needs to be done is clean it first. You can use the paper towel, yeah. And this cleaning spray. And now we'll tidy up this drilling machine.  remove the drill bit and place it in the toolbox coil up the cable for the drilling machine  just plug it out i'm just gonna bring back the tools  Place it in the drawer where it belongs. Close the drawer.  And now that the table is clean. Okay. Then I think we're finished."
    },
    {
        "category": "disassembly",
        "name": "User_14_410_1010_480.mp4",
        "transcript": " So I want to disassemble and assemble this lamp. For that I need some tools with this cross shape like a screwdriver and I'm going to look for one. First I need to turn on the lights in order to see it properly.  So now I'm going to look for a screwdriver. Hi.  So maybe I'm going to try this one. Let's have a look if it works.  I guess this is not a screwdriver.  I'm going to try this one.  maybe i need some help so i'm going to call my colleague hi do you know where can i find some school drivers with cross on it  Yeah, I guess yeah, bigger one. No, these with close on it, yeah.  So whatever you are showing me, it's recording. Is it okay for you? Maybe I'm gonna ask my colleague.  Okay, thanks. Bye. Hi, where is Lam? I also need some help. I cannot find that screwdriver.  You mean this? Okay. Okay. Thanks.  Yeah, this one is working. So now I'm going to remove these screws with the screwdriver.  Finally it came out. So now I'm going to remove this protection.  I'm also using this screwdriver for these.  Maybe I should use a smaller one, like this.  I guess I have picked the wrong one.  So I'm going to look for smaller one.  Hi, I need some help.  so i used this screwdriver for these and but i cannot remove these the smaller ones should i also use this one it doesn't fit i guess not but i'm not sure you can use it as long as it's i can hold it  Can I also use these? Yeah, you can also use these, of course. But I think it's already loose. And it's because there's another screw in there keeping it tight. So you don't need to remove this, just leave it.  Okay, then how can I remove this bulb inside it? Yeah, you can just like screw it off with my hand. Okay, thanks. So now I'm going to remove this bulb.  And now I guess I should remove these springs, these four springs. Just take them off like this.  So now I'm going to separate these arms. These are adjustable. So now I'm going to remove these screws.  Now I'm going to remove this side.  so the lamp is completely disassembled as you can see and now i am going to reassemble it so first i'm going to install this bulb  So now I want to attach this protection to these arms.  So now I'm going to put this arm inside this corner like this. It should be aligned.  So now I'm going to fix it with this screw like this. It's here.  Now I'm going to tighten it. So now I need to fix this arm into this.  So I installed it incorrectly. Now I'm going to take it off.  First I need to secure it with this ring. Now I can tighten it easily.  Now I'm going to fix these legs into this.  I guess first I should try to fix this one.  first I need to tighten this screw I guess this guy should be fixed here  First, I need to put in this one.  This should be like this.  this one is not necessary i guess so i'm just fixing this one  This screw should be here, I guess, but I don't know how to fix it. Maybe I need this for this.  I guess I did something wrong, so I'm going to remove this part again.  This one was right...  I'm going to call my colleague, because I need some help. Hi. You need some help? Yeah. So, I don't know what to do here. I cannot assemble it. You cannot disassemble it?  I mean assemble it. I think this one should be here.  And this one should be here. And I don't know where should I put this one like.  And this one just comes here together with this piece."
    },
    {
        "category": "disassembly",
        "name": "User_14_412_2309_1_480.mp4",
        "transcript": " so i am going to disassemble this set of bars with this allen key so for that i'm going to unscrew all the screws on it there are many you can see and first i'm going to detach this part this looks easier to me  so I'm loosening it so this part is removed now I'm going to unscrew this one  so now let's start with this one i guess this one looks difficult  Maybe first I'm going to detach this one.  This one is also removed. Now, I guess I'm going to detach this part. As I said, I have to remove all the screws on it.  finally I also did this one so now I'm going to start with this one here  So this one is also removed. Now I need to unscrew this one.  i think this one is stuck here my beds i forgot to remove  This one first, I need to remove this one. I guess I cannot remove this one either. Maybe.  Finally I did it. Now I'm going to remove this one. It was quite easier.  That's it."
    },
    {
        "category": "disassembly",
        "name": "User_14_412_08010_1_480.mp4",
        "transcript": " So today I'm going to disassemble my lamp in order to inspect it because there is something wrong with it. And I'm going to disassemble it because it's not working. So first I need to check it if it works or not. So I'm going to plug it in. See, it's not working.  That's why I'm going to disassemble it. So I also need to turn on the light. So now I'm going to get some tools.  So I'm going to use these three screwdrivers.  so first i want to remove this protection this cover so i need to remove these screws  So it is removed easily as you can see.  Now I need to remove these springs.  So now I'm removing these, separating these legs. That's why I'm removing this corner here.  so now i'm going to take off these springs  No, I think it's still recording. Can you see the light here?  When it's reconnecting, it means it's not working. I don't know.  Okay, you can just continue with the recording. It's still recording.  So now I'm going to remove this guy over here.  I want to remove this corner, so now I'm going to remove this screw.  So I guess this cannot be removed. Still I'm trying. No, I guess not.  So now I want to remove, take off the bulb. Oh, there is something stuck inside, that's why it wasn't working. So I need to take it out.  Because of this, it wasn't working. So I have assembled, disassembled my lamp. Now I'm going to reassemble it. So first I'm going to assemble the lower part or the bottom part.  Maybe I'm going to start this upper part. So now I'm going to reinstall the bolts.  I don't think so I can reassemble it, so I'm going to ask my colleague.  Islam here?  So first I need to give it a shot. Then maybe I can ask for help.  It should be like this. I'm trying my best.  I don't know what to do, I'm just figuring it out.  so i'm just trying to fix this color but i'm not sure if i'm doing it correctly  So I'm trying to align these holes, but I can't. I don't know why. So I'm trying my best.  So I'm going to tighten it with this screwdriver.  So finally this park is reassembled as you can see.  So now I'm trying to attach these legs like this.  It should be somewhere here but I don't remember I guess it should be like this  So I'm trying to align the holes, but yeah.  Hi, I need help. Okay. So I don't know how to assemble it, reassemble it. No, we kind of keep going. We kind of maybe assemble it together. Yep. And for a fact that, so you, uh,  This part goes together.  And I also don't remember the bottom part, how to reassemble it.  first i'll see if we have forgotten anything here because did you also remove this or yeah i had to remove this because okay now we should probably take this out once and fit both of them so this was inside here  But I guess the hole is broken, so. And did you also take this off? No. Okay, then how did this fit in here? Okay, the hole is broken, so this comes here like this.  It should still fit somehow. Can this come off? That looks like a...  So we have these two. Okay, so this moves. At least that's a relief. Maybe you should align the hole.  The plastic part is really causing a lot of problems. Because it's not really aligned well. And now it is aligned. So now I can close this. And then align these two. Finally place this in here.  this was here or are you sure yeah it should be inside this one but you're sure that this was here yeah i guess  mistake okay before fitting this maybe we should also think about this so this part comes at the end we don't need to worry about this but this part here is important  in this kind of fashion this looks good and that should come in here I guess  so where these play parts are not yet shown so one was in the middle okay good point between these two mm-hmm yeah  and one was here or yeah between this or no was it like this or  Maybe this one was in the middle. You should also put this one.  These two were in the middle and this one at the end. Perhaps we could take this off. So two were at the end and one was in the middle. Okay. So two small ones. This was at the beginning.  What are equal to? I'm not sure.  So this one wasn't here. It was here between these two. Yeah. So then we'll fix these springs. Yeah.  And hang the springs inside, okay. The second one. And fill it like this. Hmm.  The friends are supposed to attach here? Yeah. Okay, I understand. The problem is there's just two little space remaining here to attach anything. I'm not sure honestly about that.  this part but maybe we can finish this end  now this one comes in  this comes here right so we don't need that so i put the washer and  How are we?  You're sure that this was here in the middle? Yeah. Okay, so then I'm going to push this.  Mm-hmm.  This is big enough. Okay, at least it stops. And then accent these prints here. If I understand correctly. But we can do that at the end. Once we finalize the rest. Where else is uranium? This. These two. And these two.  So this was here. Okay. I think you're unscrewing it, not screwing it. Oh. Mm-hmm.  just won't fit so we would have to click on this and fit it during the operation try that  Then the second slot. Then this one, then this, I guess.  Can you hold this in please? This here, because this will otherwise just automatically fall apart.  Let me go for a minute.  so let's push this first of all to this side and then  I guess you also need to put this one here. Yeah, but it won't fit. It's too small.  a incorrectly placed one kind of almost because I think it is acting like it's going to be like fit in this way through  And how to attach this protection here.  that are sort of still remaining so you also disassemble this or yeah then i reassembled it but okay but this should go then somewhere inside  Should I check if it's recording or not?  This pin also comes off, right? But I didn't remove it. At least I can remove this part. Hopefully we can access that. Yeah, this one.  can you lower it so i can see this thing is definitely in  Like here.  because it just doesn't align very well but we can take this as a temporary solution no it does not align so it needs to align like this this is magnetic no  I'm sure there's supposed to be this, maybe with the washer  I think that this should have fit around here.  And this. I think the corner should be like this. Aligned with the... It was like this. If it was like that, then this whole thing would be reversed like this. I...  makes also sense so this is the lower part in that case  This. Then this. This is what I was talking about, like this sliding through here, like this. Then it can move a bit more freely.  Now we can, first of all, fix this. I think the direction of these corners should be opposite. Of which ones? This corner should be on that side, I guess. This one. Because if I mount it like this, it should, I think it would fit. And this should be like  But it doesn't matter, I think. Okay. Or if you do it false, then I'll just say it is. Put this in.  So in this case, it actually is very flexible. It is not rigid at all. So we probably made a mistake somewhere. So can you put it down?  Yeah, it was like this, I guess. The least that we can do is just finish this. Place the washer and tighten the washer up.  Give me at least test it.  I think you need to tighten it first. And this thing, you can tighten it.  But here, I guess it is a bit too... Still, so I think... Here somewhere there was an inaccuracy, but can you plug this in? Yeah, sure. Still, it's not working. Yeah.  Should I unplug it?"
    },
    {
        "category": "disassembly",
        "name": "User_14_1410_2110_1_480.mp4",
        "transcript": " Okay, so today I want to disassemble this thing and embedded computing unit. So first I'm going to remove this wooden plate. So I have some tools here and I'm going to use these tools to disassemble this thing.  So the wooden plate is removed and I'm putting it aside. So now I need to remove this upper part, this plate, metal plate. I need to unscrew all the screws, there are six in total.  I'm just untitling the screws Now I can take it off easily  And I put it here. So now I want to remove, disconnect this green power connector. First I need to untighten the screws with this screwdriver.  So now I need to take off this part. So for that, I'm gonna use this screwdriver.  Just unscrew.  I'm also going to remove this part Just unscrew it  So this one is also removed and I'm going to put it here.  Now I'm going to take this part out. This is called RAM chip.  So now I'm going to take these metal plates off.  So now I need to remove this bottom plate in order to take out the hard disk.  So this plate is removed. So I don't know which one is the hard disk. So maybe this one is the hard disk.  So first I need to disconnect these cables like this.  so i guess this is the hard disk and i want to remove it first i need to unscrew it  so as you can see the hard disk is removed properly or successfully  So I have disassembled it completely."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_1_1410_1_480.mp4",
        "transcript": " So I am looking for an Allen key.  So we are going to use this Allen key. Did you find it? Yeah, this. Okay.  They're also fitting quite well. OK.  Should I also take the phone with me?  Close the light. Close the door.  I think this was not properly fit, that's why it bent this easily. First, I'm going to remove the charlie out of the way. I think next, what we can do is start with...  So we are doing it together, like we are going to disassemble. Yeah, exactly.  So first we should remove these corners or just cover? So I think first what we could do is just remove this.  This one is stuck.  So we can put this flat here. I'm going to put the spare parts here inside. So for this bigger one, I think we can just start with these four screws.  I think you can take the larger one.  I think we can use a flat head.  carefully push it out  And this, top five.  and here i guess we need to loosen the these two and from this side these two maybe we can also take this out at this corner i'm going to remove this one yeah  this is using and this is using screws off they are all identical I think  You could take this off. Take this off. Do you mean this part? Completely. It's gone.  This is the one.  Maybe I can hold it. You can do it.  And it's separated.  Maybe it is a good idea to loosen also from the other side. I can also loosen this one.  I'm going to fit this in. This is not a good fit for this one. Maybe that one. What I can try and do is take a careful look at the other parts. So we have different caps.  And taking this off is going to be more challenging. So I guess we can consider the assembly process complete for now and continue.  Should I stop the recording now?"
    },
    {
        "category": "disassembly",
        "name": "User_14_User_2_407_2210_1_480.mp4",
        "transcript": " So I'm still putting on my gloves.  Okay.  Now you can do the rest here, on your side? Yeah, you can do it here too.  Yeah, there are two.  So now we can take off the cover or not?  Oh wait, I forgot. I forgot one. Hold on to the leg.  So now we can remove the bolts that are holding on to the rod in the middle. You mean this one? Yeah, like this is the rod and they are like two screws. Yeah, two are... Here? Here? And here? Here? You mean these two?  But it says Allen keys. Only those are Allen keys. Okay, let's try this first.  Thank you.  It's not moving, yeah. I guess we should also, yeah, okay.  So we are going to remove this one. It can also be removed.  I think it says here the connecting rod from the inside. So this is the connecting rod, I think. Okay. Now we can use the electric drilling machine. For what? For these.  I think this is good. Maybe this one. Yeah. Can you plug in with it? Yeah.  No, but what can we do?  but we cannot remove this roll okay i mean just says like separate the two legs and we can do is  so the legs are separated  okay so we can look at the bottom and remove those screws here okay  It's not moving. It's not? You can just untighten them. Thanks.  Should I also remove the others?  Where are you for school?  Let's just clean up the tools a bit. I can do the drilling machine. Can you sort those in? Yeah, sure.  Blue ones in here. Yeah, the colored one.  So the black one was from here. I'm not wearing my glasses yet. The glasses are too hot. Yeah, okay. Stop the recording. Yeah.  Yeah, we can press start."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_2_411_2310_1_480.mp4",
        "transcript": " Thank you.  So we did you put it out of school today?  These two, yeah. Okay.  That's right.  So now we need to reassemble it?  Okay."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_16_407_1712_1_480.mp4",
        "transcript": " So first we need to find a tool. Maybe we'll be using this. We need this or we don't? I guess.  So first we need to remove this vertical bar. This one.  So now we need to remove these plates. Can I have that one? So you're blocking the camera, maybe you can...  I guess, maybe later.  Can you also remove this one?  Can I have those screws? Yeah, this horizontal bar. So it's this one.  Yeah.  Can you hold it? Okay, it's in your ring. Yeah. And do I need to remove this? No.  Yeah, but now we need to clean these blades. Great.  It's okay.  Yeah, that's it. Can I have those screws? Yeah. Can you put that on the desk?"
    },
    {
        "category": "disassembly",
        "name": "User_14_User_16_412_0402_1_480.mp4",
        "transcript": " Yeah, this fits.  you're blocking the camera these two  These two or these two? Okay, okay.  Bye.  Next remove this triangle.  Was it like this or? Like this. Okay. Yeah.  I have the alarm key. Which one? Okay. There's the alarm key.  Mm-hmm. Mm-hmm."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_16_412_1510_1_480.mp4",
        "transcript": " So today I want to disassemble this lamp with my colleague Boson. So in this task we are going to use some tools. Screwdrivers. Observation. There's also some screwdriver.  It doesn't fix, yeah. So, yeah.  So maybe I'll be using this screwdriver and this. Okay. So first, I guess we should start from here. Yeah.  so you're just checking the tools or what okay remove the ball yeah so first we are going to remove this ball yeah  so the bulb is removed and i put it here this cannot be removed i guess yeah yeah just remove these screws over here yeah you can use this screwdriver  easier to remove the next one with my hand  remove this triangle shape also from the back side so the protection is also removed and this thing is de facto I think it's dropped out it's broken from the side so this small  Yeah, it was here. No, I guess not. We cannot remove this one. So yeah, remove these springs.  yeah it takes some time  And I'm gonna remove other screws. These are separated. So now I need to remove this triangle.  Do you know if we can remove this part? Yeah, I think you can. I'll try it. Yeah, I guess.  I just remove this one like over here. Pulling them apart. Take this one out.  Is there any screw here? No, it doesn't have a screw, but it's stuck. Because this cannot be removed. Yeah. It's more easy. Let's just turn it around and put it on. Okay, this part is already removed. Next, we can remove the bottom part. Remember the shape. This shape.  so i guess you're tightening it's not sure okay  So now you can see the lamp is completely disassembled. Yeah, okay.  There is another screw here. No, it's just... So... Now, remove this part. Now every part is removed. Except this one, this one is not able to move.  So now, okay."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_16_451_1102_1_480.mp4",
        "transcript": " Thank you.  Should I press it down? I don't know how to open it.  I'm trying to slide a little bit.  like this then slide  This part, yes, and you can lift it. I think it's, yeah, it can be like this.  Yeah, the fan is also inside.  I think I should use it  a screwdriver this is also a screwdriver no it's not you can see it's different okay  there are six  which one this one  how can i remove it by unscrewing okay  It doesn't need to be disconnected. It doesn't need to be removed.  There are four bolts for the CPU so you send the proper screwdriver to remove.  We remove the CPU. The big one is the CPU. You mean this one? OK. The whole thing. OK. And now I have to disconnect the cable of the GPU. OK.  This one fits in, yeah.  Thank you.  All of them? They are each in total, okay. These two also? Yes, they are. Okay, all of them. They are 10 in total.  Now, please attach the connection to the motherboard. Just a little bit.  okay there is one left here I forgot to remove this one  gently, softly, slowly, carefully. Lift it, lift it, this spring.  How can I take it out?  You can see here it's inside.  Okay.  cable to the motherboard or cable you can see like this this or the the the the orange one the orange one yes the data cable and also and also this this little white one  and i think there is one more we have to remove okay so the cables are removed and these two we do it later so now we remove the right yeah the black press in the bottom here also  It's already removed. It was here. Or you can use  I have an Allen key here.  It's not coming out. You can see here it's stuck, so just press it and it's off right now.  And now let's see which cable we can disconnect. These four, okay.  Okay, so now we disconnected most cables. Now I sort the parts and put them together."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_16_451_2901_1_480.mp4",
        "transcript": " Okay, I start.  So now we are going to do this disassembly task and I will teach you how to do it. First, we should put the clothes on. And next, this is all tools we need.  So what should I use to remove this one?  So for this, I should use another Allen key. Which one should I use? This one.  Ah, it's already closed. It's stuck, I guess. All right. All right.  So what should I do? This one?  Can you also put this too? These threads.  Maybe you can do that side.  But you didn't remove this one.  It has four wheels. First, you need to turn this around. You can find the visible key.  Should I use this one? Should I also remove this one?  No, not this one. It's really bad.  I think this should also work. No?  Can you hold it here? Like this.  I can't see it from here. Can you put it like this?  Do you need to be fully out to do this?  Should we also clean these weights? All the tools here.  Do we have a spray bottle?  Thank you."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_17_407_0601_1_480.mp4",
        "transcript": " So first we need to put on the gloves.  So we'll be using these tools, right? So now we are going to remove this vertical bar. This.  CONFERENCE.  Thank you.  This is the Wallerman. And the wheels. Okay.  So there is only one?  Should we also remove these?  These are too tight. It's not warm.  Too tight? Stuck or? Is it stuck?  so now we need to remove this horizontal bar  So you can use this one. Yeah.  Thanks.  Tools.  Thank you."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_17_407_1712_1_480.mp4",
        "transcript": " Surfers for me to put on the gloves.  So first we need to remove this part, the vertical part.  now we need to remove these plates  Together?  Two, three.  And now we need to remove this. The horizontal part here.  OK, here's this one.  This one? Or is it?  Okay, yeah.  Okay, yeah.  Okay. Now we need to clean.  Bye.  Okay, so we are done."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_17_411_2810_Table_Disassembly_480.mp4",
        "transcript": " So first we need to remove this wooden top. We're going to take off this light.  You mean this one? Did you unscrew it or not?  Maybe you can use this one. Okay, sorry. Yeah, we need to put on the gloves.  Is it working or not? Okay. So I'm putting them here. Can you see it or?  We have to mark the front side. Okay. It's already marked, yeah. So we will remember the front side and move this.  so we should also mark on the other side let's take it off uh should we put it here on the floor or  How can we remove that?  So we don't need to disassemble the legs. Everything, yeah. So you have two island keys, can I have one?  So this one fits.  Can you also unscrew this one? I cannot move it. It's not moving.  How did you remove these screws? Like with what? This one? The bigger one. Yeah, okay. With the bigger one, you know, you have to.  So did you also unscrew the smaller ones like here? Not yet. Oh my God.  Now we can take off the door. Is there one here? Is there a scoop here? There's two kinds of scoops. Yeah.  so i have this one is already removed so we need to use this rule  So for removing these, you can use the drill machine. Like last time with these two, you can remove it with the drill machine. And I'm going to remove these over here. These two? Yeah, these two.  I can hold it here for you.  This one is too big.  Maybe take the smaller one. Too small.  Doesn't fit.  Mmm.  Yeah. It doesn't fit. I'll leave it.  Did you also try this one? This one looks better.  It's right on the other side. Perhaps the school is stuck or what? Yeah, the service is kind of damaged. So... Yeah, I know. Oh, it's not this cross. It's...  Maybe try with this one. Which one? This one? Yeah. It's a cross. It should be... Like a star on it? This one is a crosshead. So we don't need it. Star heads, yeah. Not crossheads. It's small.  this this one looks bigger like this one probably too big  But it's not coming out.  for is it moving or not yeah it's moving  Yeah.  We also need to remove the bottom part. Is there any part we have to remove? No, I don't think so.  Mm-hmm.  so everything is removed and we don't need to remove anything else i guess  Was this one here or? There's some cross, stars, there's some symbols here. There you can find your place. Should we sort it or? Yeah, no.  No, we should take off our videos."
    },
    {
        "category": "disassembly",
        "name": "User_14_User_17_411_3010_1_480.mp4",
        "transcript": " Thank you.  So I need to take off the wooden top like this.  With an Allen key? Yeah, exactly.  So I'm going to remove these.  This is the middle one? Yeah. With what? And Allen Cure is arranged. Yours are two rows. Here. Yeah. There are two rows.  Then the middle one.  Thank you.  Can you hold it here? Are these the same? Yeah, they are the same size.  So there's a wrench here. Which one should I use? The other one?  I can only loosen it. I can only loosen it. I can't take it out like this. No.  Yeah, I'll send it, but it's not coming out.  Can you hold it like this? I have never used a wrench before.  Which one? Finally.  So is it done? Yeah, I guess"
    },
    {
        "category": "disassembly",
        "name": "User_15_410_0411_1_480.mp4",
        "transcript": ""
    },
    {
        "category": "disassembly",
        "name": "User_15_410_2110_1_480.mp4",
        "transcript": " Okay, so I want to disassemble this embedded computing unit. So in order to do that, I'm first going to take off this zip tie with this box cutter. So I'm going to slide this knife out. And then I can use that to cut...  to cut this zip tie like that. And now this cable is loose. I can take this out and then I'm going to disconnect the unit from the wooden plate. So as these are screws with a crosshead, I'm going to use maybe this screwdriver is a bit better because it's thinner, so it won't be in the way. And I'm going to use that by turning it counterclockwise to unscrew these screws.  And I'm going to put them all in a pile over there so I remember where they go. And now I'll do the same on this side. Just again, taking these screws out by rotating  Counterclockwise, same here. And here.  And then now that I've done that, I can take the side plate off. So for that, I'm again going to use this cross head screwdriver because these are cross head screws. And maybe I'm going to use this one because it has a bit of a better grip. So just again, turning counterclockwise, I can take this screw out.  And I'm gonna, first I'm going to take this knife back out so I don't hurt myself. I'm gonna put these on a pile over here. This one as well.  Just unscrewing counterclockwise. And this one. Okay, and now I should be able to take this out. And in order to do that, I am going to open this hatch up so that I have something to grip onto.  just have to unscrew it a bit more and then i can see if i can take this out somehow there we go and put this back here maybe screw this back on because i don't actually need it to be loose  Rotating clockwise. So I'm going to put that over here and I can do the same on the other side. And actually I can also take this off of the wooden block and I'm going to put this over here, turn this around.  and remove this part. So in order to do that, I'm just going to remove this power unit. So I'm going to use this tiny screwdriver to get into these holes and unscrew counterclockwise. Take this out, the same over here. And now I should be able, maybe a bit more, actually.  then I should be able to take it out. There we go. I'm just going to store this right there, and then I can take the side plate off as well by just rotating counterclockwise to take these screws out.  Put that here. Again, rotate counterclockwise.  Here we go, and now I can just take this side plate off and put it over here. And now I'm going to flip this around so that I can take these off, these connectors, by again using the screwdriver to rotate counterclockwise. I'm also going to put these in a small tile over here.  I'm going to put them with that over there and then do the same on the other side by again rotating the screwdriver counterclockwise.  I'm also going to hold it so that it doesn't fall down while I unscrew the last screw. There we go. And now I'm going to put all of these over here as well so that I don't lose them. And then now I can take this bottom plate off by again using the screwdriver and rotating counterclockwise. So there's one.  Now all the screws are screwed out, so I should be able to lift this up. I'm going to put this off to the side over here.  And now I'm also going to take the top plate off, so for that I'm going to flip this around. And then take out the screws up here, again rotating the screwdriver counterclockwise. I'm going to put them all in a pile over here.  And put that over here as well. These ones as well. And now I should be able to take this off. I'm going to place this to the side here. And now I can take out this RAM chip right here. So I'm just going to carefully open these clamps like so.  First on this side, then on this side, and now I can carefully, or I should be able to carefully take it out. And I'm gonna put that over here. And now I'm also going to,  take out the hard disk so first I'm going to disconnect the data cable and then I'll disconnect the power cable and I can take this out by again using a screwdriver and rotating counterclockwise like so so  And again, I'm just putting them in a pile over here so I know where they belong. There we go. Now I can take this out and put this over here with the corresponding screws. And now I think I've disassembled everything.  And that concludes the disassembly."
    },
    {
        "category": "disassembly",
        "name": "User_15_411_2309_2_480.mp4",
        "transcript": " Okay, so to disassemble this camera mount, I'm first going to start by unscrewing these small screws to unscrew the camera. And I'm going to do this by rotating this small Allen wrench counterclockwise. Maybe it's better this way. There we go. And the second one, which we have to be a bit careful that the camera does not fall down.  And there's the screw. Okay, secondly, I'm going to detach this small metal part by also rotating the Allen key counterclockwise. There we go. All right, and then next we can slide this part out and unscrew this top part.  by also going counterclockwise. It's a bit hard. There we go.  Just unscrewing and you can use your hands to finish it. And then we're also going to unscrew this angle type thing. Maybe to make it a bit easier, I'm going to lay this down.  There we go. And then just again going counterclockwise. And we can also slide this part out. Now to detach these two, I'm going to use this Allen key again counterclockwise to unscrew this screw.  And to take this out. You can also slide this part out. And then use the Allen key again counterclockwise to unscrew this screw. And first I always use the short part and then I use  a long part. And slide this part out. And now we only have this part left. And because the screw is inside to disassemble it, I'm going to use this screwdriver. Also again, counterclockwise. And slide this part out.  And everything is disassembled."
    },
    {
        "category": "disassembly",
        "name": "User_15_411_2410_1_480.mp4",
        "transcript": " Okay. So today I want to disassemble this lamp. So in order to do that, I'm first going to take it off of the clamp mount and then place it on the table. And now I can see what kind of tool I need. So it looks like I need a cross head screwdriver. I'm going to look for one of those. And I think the most suited is probably going to be this one. And I think it's already the right size, but if not, you could change it, I think.  Yeah, it's the right size. Okay. So first, I think I'm just going to take the lamp head off by unscrewing these bolts up here. And to do that, because in the back we have the nuts so that the screwdriver can actually grip, I'm going to kind of hold onto the back of the nut and then rotate the screwdriver counterclockwise.  And I'm going to place all the pieces that I take off of this part in a pile over here so I know where they belong. I'm just going to take this one off again by holding the back.  And now this one, since it doesn't have like an actual screw head, I'm just going to use this hand twist to take it off. Again, just rotate it counterclockwise. And then just store that all over there.  So I'm going to put all of this in a pile. And then next, what I want to do is I want to take apart the middle part. So in order to do that, first, I'm going to take off these springs and put them in a pile over there. And then I can now just unscrew these. Maybe first I'm going to unscrew these spring hooks actually. So I can just unscrew that and then push it out. Maybe.  Seems like I might actually have to screw it out.  There we go. I can just put this over here in a middle pile and then take these screws off by again, holding the back and then just rotating counterclockwise.  And I'll do the same over here. And put these plates over here as well. And now all that's left to disassemble is the lower hinge. So in order to do that, I milk again, going to first take off the springs.  Put them in a pile over here and then just unscrew the screw right here. Again, by holding the back as well. Like so, and now this part I can use the hand twist again.  and rotate that counterclockwise. I'm going to put this over here. This part, the slower removal bar and the mount. And now I think everything  is disassembled. I've ordered everything into piles so that the next person can reassemble it knowing which pieces go where. And yeah, that's it."
    },
    {
        "category": "disassembly",
        "name": "User_15_412_1510_2_480.mp4",
        "transcript": " Okay so today I want to disassemble this port block so in order to do that first I'm going to turn on the light so that I can see properly and then I'm going to take it and put it over here on my workstation and then I'm going to get the necessary tool which I think will probably only be this screwdriver with a cross cross head  Okay, and this is just the adapter with the cable. So I think what I'm going to do first is I'm going to take these screws off on the side so that I can remove it from this wooden block. So to do that, I'm just turning the screwdriver counterclockwise like so. Do the same over here.  and over here now for the last screw it's just the same again just rotating counterclockwise  like this and now I should be able to take this off which it is still connected to the wooden plate so I'm just going to lift this and then turn this so that I can actually place it on the on the table  like so, and we can maybe look at the bottom. So the bottom here, just these things are attached. Sorry, I'm going to take those off. So I'm just going to flip this around. Whoops. And then use this screwdriver again to just unscrew these by rotating counterclockwise. Nope, that's a bit farther than I thought. I'm going to place these over here so that I remember which part of the thing they belong to. Same over here.  this one as well. And this one again, just rotating counterclockwise. Oops, I'm going to place that with this one. And then I'll do the same on this side again, just unscrewing by rotating the screwdriver counterclockwise.  And I will do that for all four of the screws that are holding this bracket to the port block. Like so. I'm just going to put this over here. Now I think I can unscrew these parts.  So I'm going to just try and see by rotating again, kind of clockwise. I'm going to save these. I'm going to put them on the middle board, the wooden board. So again, just unscrewing clockwise. This one. This one. And this one.  And then finally again, just going to unscrew the final screw by going counterclockwise, which is a bit, it's not really gripping. Maybe let me see if I can get a different screwdriver. Maybe this one will work a bit better.  There we go. So I'm going to put this over here and we can, or we should be able technically to lift this part up. I don't see where else it would be secured.  There we go. Okay. And we can look inside here. So we have this part, which is a bit sticky kind of, and this big part. Okay. So in here, we can take this off, I think. So I'm going to do that by just  Unscrewing these, putting them all in a neat pile over here.  go and now the final one again just by rotating the screwdriver counterclockwise and now we can lift this part out and take a look at it it's a bit I don't know how to describe this it's a bit like oily but not so  Yeah, that is that. You can also unscrew it from here, I think. So I'm just going to place that in there again. And then we can unscrew this part. And I'm just going to put that in a little tiny pile over here. And this one's just a bit harder, so I'm going to try to use this screwdriver instead.  There we go. And now these and this one. And now if we lift this up, this should just slide right out.  Like so. Yeah, I am going to just slide this back on though to keep it safe. There's not much else that I can unscrew right here. What I could unscrew, I think, is probably this part. But I don't think I could take any of this off anyway. So what I'm now gonna do is I'm just gonna turn this, flip this back over.  And then we can maybe take off this top covering by just taking the screwdriver again, rotating counterclockwise to take these screws out. So I'm just going to put these over here. And these are the same as these, which were for this covering. Again, by just rotating counterclockwise  maybe a little bit more like so and this one as well okay maybe I'll try this one first  There we go. I'll try to get this one out again. There we go. Okay, now I think we should be able to take this covering off, if I'm not mistaken. Maybe if I use this to kind of leverage it, or can I push it around? It doesn't seem to budge.  um so i don't think i can actually take this off what we can take off however is on this side i can remove this screw by rotating counterclockwise and i can remove or well i can open this part which i'm not sure what it's for but  And now I'm going to try and remove these screws. So again, just rotating counterclockwise and putting them in a neat little pile over here. This as well. And this one.  like this. And then I can try and remove this part. And we can take a look inside here. So this is where we unscrewed the thing before. And then here are a bunch of buttons and LEDs, which I don't think we can do anything with. But maybe we can lift this up now.  Oh, we can kind of on this side, but not really. Okay. So, uh, yeah, I'm just gonna put this over here with these four screws so that I know where they belong. And then I'll take a look  On the other side, which I'm pretty sure we can also remove. So we're going to do that just by unscrewing these screws counterclockwise. Like so. And also down here. Oops. This one.  this one goes over here and now this one at the bottom all right and now we should be able this should come off all right because this is screwed in there i cannot take it completely off um  Try to take this off again, but I don't think it will budge. Yeah, so I think we've disassembled everything we could. And that is this port block, I guess you could call it disassembled."
    },
    {
        "category": "disassembly",
        "name": "User_15_412_2509_1_480.mp4",
        "transcript": " Okay, so before I start doing anything, I'm going to again put on steel cap shoes. First, I'm going to take my own shoes off. And then I can put these on by sliding my foot in and then tightening them by turning this wheel to the right. So clockwise.  And the same on the other foot, slide my foot in, press this button down and then turn it clockwise to tighten them. And now I'm first going to tidy up my workspace by removing this monitor and the mouse and putting them off to the side.  and then we can go grab what we're going to disassemble. Okay. I'm going to use this big wagon to transport it.  And I have to turn this around because I'm going to open this door. So now I can move this wagon in here and then open the clasps on either side.  and then lift the assembly over into the wagon and close the latch again. And now we can bring the whole thing over to the other room.  Okay. Now to bring it in here, I have to open the door first so that I have room to bring the big wagon in. And then close the door. Turn on the light. And we can bring this over here to the workstation.  And I can open these latches to let down the door so I can more easily lift the assembly out. Going to take the tools.  over to the workstation. And we're going to start by prying off all these caps using a screwdriver. And we'll start over here  And also this one. I'm just using a screwdriver to leverage these caps off. Also on the bottom here. And over here.  So I'm just using the screwdriver as a sort of lever to pry my caps off. And now we're first going to take off this big plate by I think using the red Allen key, which is a size five. I'm going to turn it counterclockwise to loosen the screws.  And so I'm using the short side first to have more force and then I can use the long side to turn it out quicker. Also on this side, again, the short side first and then the long side to unscrew the screw faster and I'm collecting them all over here.  And now we can take this plate off. Put it over here with the screws so that we know which parts belong together. And then I will use this purple key to detach this part. Or actually I will use the red key which is a size 5.  And again, going counterclockwise first to unscrew it.  Okay. And now the third screw. Again, to get this bracket off, just turn it counterclockwise. Oh my God.  Okay, so I am using the short side so that I can have more of a leverage power so that I can unscrew this and take off the screw as well as this little metal plate. And then I'm going to do the same down here again, going counterclockwise with the short side first to help me loosen it the first time. And then I can take this off.  and unscrew it properly. And now we have taken this bracket off and we will do the same on the other side. So again, first going counterclockwise with the short side so that I can loosen it and then I can unscrew it with the long side.  As well on the bottom, first the short side to loosen it, and then the long side to unscrew it faster. Again, using the short side to go counterclockwise to loosen it. And then the long side to unscrew it a bit faster.  Also on these two bottom screws.  Okay, now we have unscrewed both metal brackets. I'm gonna put each of the screws with each of the brackets so I know where they go when reassembling it. And then I'm now going to take this bracket off so that I can take this short metal rod off of the big long one. Again going... Now we'll need the purple key.  or not going counterclockwise.  Also on this one. And I will need a bigger key to take that off. So I'm going to use a size 6. Again going counterclockwise.  Like so. And now I've taken this part off. We can stir that over here. And we can disassemble these parts. By taking out this screw first.  And then this one so that I can loosen the small metal bar from this angled bracket.  So I can't really loosen the screw. So we're just going to leave that on there for now and move on to the other side, which we're going to do the same for. Again, loosening it, going counterclockwise.  So these ones down here and down here, I can't really loosen. So I'm just gonna put this one back as well. By turning it clockwise. And over here as well.  And I will instead try to take this off.  And now we have this big part loosened from this. And we will do the same on the other side. So loosening this screw by going counterclockwise. Then being careful not to drop it when it loosens.  And then we can take this part off too. All right, now to put it all back together, I'm"
    },
    {
        "category": "disassembly",
        "name": "User_15_451_0702_1_480.mp4",
        "transcript": " Alright, so today I want to disassemble this workstation computer. So in order to do that first I'm going to have to open it up by sliding this out. And opening it up like so. Take this out and  Put it up here. Okay, now I'm going to carefully lower this onto its side so that I can get a better look on the inside. There we go. Okay, so let's look at the instructions.  Okay, so first we're going to remove this chip rack. For that we just have to basically unlock it and move all of this to the side a little bit so we have more space. And then we can just slide it out. I'm going to place that over here. Next I'm going to remove this duct or covering which is clipped in over here. There we go.  now i'm going to remove this fan over here so for that i'm going to use this one ah maybe first before i touch all of these parts and they could be a bit sharp i'm going to put on some gloves and then i can detach this  all these screws i'm gonna keep in this little box so that i don't accidentally lose them and now i can take this fan out obviously i have to unplug it too i'm gonna place that over here all right next i'm gonna try to remove this gpu so in order to do that i have to take off all the bolts from this frame  So I'm just going to do that real quick by rotating the screwdriver to the left, so counterclockwise.  i'm also just gonna store all of these screws in this box over here all right and now i should be able to take this off if i slide this back maybe first i'm gonna detach the cables here there we go they're all  disattached now if i pull this back and pull this up at the same time nothing else is attached i should be able to get it out there we go i'm just gonna place that over here okay i've removed the gpu  So next I'm going to remove the data and power cables from the HEDs. So I'm just going to take these out one by one. There we go. And now I can also take these out by pushing this in on either side and then just sliding it out.  I'm gonna put these over here. There we go.  I've taken those out and next I'm going to remove the ram chips. So in order to do that I just have to open these on either side. Now I can easily take them out like so. I'm going to place them over here.  Next, I'm going to remove this heat sink. So for that, I'm going to use the screwdriver again because it's a crosshead and just unscrew this.  And now I can just lift that off, place it over here, and then I can take the CPU off. And for that, I'm going to need a star tip. So I'm just going to unscrew that. Like so, on all four sides.  Okay, and now the frame comes off pretty easily. I can carefully take the GPU out as well. Place that there. Now all I have to do is to take this battery out and for that I'm going to just use this to press this lock to get it out.  There we go. I'm going to place that in this box. I know this is optional but I am just going to unplug all these cables from the motherboard. So this one. This one. This one. This one. Take this latch to unplug this one.  And then all of these cables for the HDD. And this big one as well, if I can. There we go. These are already just attached. I'm going to move this one.  This one as well. And now over here we just have this tiny one, this tiny one, and then this slightly bigger one. Okay. Now I think everything is unattached. All the parts are sorted.  So I think we're done with the disassembly."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_1_411_0910_1_480.mp4",
        "transcript": " So I'm going to take this and put it all over here on this table. Or on the side actually. It's a good idea to disassemble the table in the other room so we can hold this and put this  And then I'm going to close the door. And I'm opening this door.  so that you can get in a bit easier. I'm going to move this ladder out of the way. And then I'll close the door again and turn on the light so that you can see better.  And to disassemble it, we need Allen keys because of the hexagonal shape of the screws. And those, I think the right size is probably in this cabinet here. I think maybe this one.  Do we need a smaller one for the other screws? That's bigger, I think. Okay. But do we need are these smaller? I think so. Right. We need. Maybe this one or this one.  No, that's too big. This one. I'm going to put this back and close it back up. Do we want to show how it works first?  Antiglockwise it will move up and moving it clockwise will push it down slowly. So the assembly is functioning and working properly. Okay, so do we take this plate off first with these screws? Yeah. Maybe? I can look if I can find another one of those.  of that size. This one's too small, I think. Yeah? Okay. I'll go on this side.  And I'm rotating counterclockwise. The same on this screw. First I'm loosening it by using the short end. And then to make it a bit faster, the long end.  And rotating counter-clockwise to unscrew. I need to put these screws down here. Sometimes it's a bit stuck.  okay and now to remove the upper casing we have to unscrew the bigger screws by again using an allen key and rotating it counterclockwise  If I use the long end first, it's a bit harder because I need more strength to loosen it. But if I use the short end, it makes it a little bit easier at first.  And I'm going to put them all over here. And hold onto the tables. Oh, we have to pull this out. You just pull it out. Okay. The crank is now...  I don't think we can remove anything else I mean maybe these two then you can take this out but you'd have to remove this long part as well you need a you need a screwdriver  this one or is it too big? Oh, I didn't see that. I don't know if we have one of those. Maybe if we use, um, one of these, yeah. We also usually had,  like a screwdriver that you could put the drill bit on. But I don't know where that is. We push it back in. Or from the bottom.  Can I? No.  Oh, but maybe now. Oh, it's stuck in the back. There's like a like a hanger that it's hanging on. Yes. So maybe if we feed some of it back through a lucid because there is a like a small tab and it's stuck on that like a coat hanger kind of. But it's not. It's maybe if we have if we have like something long, we could maybe lift it up, I think.  or like, yeah. That's not sturdy enough. Maybe if I use it like this, cause then it has more or less flexibility.  It's too short. Yeah, this way it's too short. Maybe it's a better idea to find a screwdriver that can do this. I don't know. Or maybe we could use the metal plate of the table. If it fits through here.  I got it. There we go. I put it over there in the box. There should be one that fits.  And meanwhile I can look for an Allen key that fits that. Which maybe, maybe even this one will. Yeah, this one fits. So I can unscrew this by rotating it counterclockwise.  And then I'll do the last bit by hand. This one as well.  Did you secure it? You can just turn at the top part too. If you just  no just the black part somehow you should be able to turn it because i used this last time but just the black part not the whole yes like this and then you can stick this in there it seems to lock at this point no no if you go that other way yeah  I think some more. Yeah. And then it has to. It usually clicks again if you turn it. Maybe this one doesn't. I can try and.  Or maybe first we can move it all the way down because it was wiggling or not. Yeah.  and the first bolt is out and the second bolt  and now the second boot the third boot is also out the last one  If we, I think we can slide it. I'm just gonna take these two and put them over here. Maybe if I hold onto this part. And you can also technically take this part off, but there is a zip tie here to prevent that. And it's very greasy.  We don't need to take this off. So we lay this. It's unstable like this. So we would lay this down. And the disassembly process is now complete. Okay."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_1_411_2910_1_480.mp4",
        "transcript": " So let's first, we get some tools. So you can empty that trolley and bring it together.  Mm-hmm.  Oh, sorry.  Back to the other room. No, I mean just here.  Do we just flip it or can we just take it off like this? Okay.  How is it attached? It is attached using the screws. So there is two on this side.  There's a screw somewhere on the inside here. But it's moving, isn't it? Yeah, but this side is not moving. Oh. And I cannot reach it without going in here.  Mm-hmm.  This is your temporary solution. Maybe we can put the trolley. Can we not just use this? We cannot move it because if you check the wooden desk is in the way. Or maybe we can move the desk.  Yeah, I think that should be sufficient.  you can just place it against there like with this back  Yeah.  But you could do like the big screws and I can do the small screws.  So we have to start the dome. Oh, this doesn't... Okay.  I think they are quite...  Okay. So I think these have the same size. I think this was placed here to guide the crack. Mm-hmm. So I think I'm going to screw first the outer ones and then the inner ones. Okay.  Tightly fixed. You have to go the other direction. Like this way. Am I screwing it? Yeah, you're tightening it.  Now the...  There.  Mm-hmm.  The process is complete."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_1_451_0602_1_480.mp4",
        "transcript": " But we will shout.  We've completed the first step.  So we see that this is done. The next thing is when you remove the duct. I think the duct is sort of locked in place on this fan here. So you need to take it out from here and pull it a little bit so that it releases. And the coloring.  Because this is really loose.  RAM chips, you need to release the latch from both sides. Oh, at the same time. Oh, no, you can do it at different times, but you need to do it on both sides.  And I think it might be easy now to remove this fan because this is the fan one. Fan one is this. So we need to, I think this is attached first of all here with this cable. So we need to lug it out.  and then unscrew it here.  So first we can remove all the cables that are attached here.  so this here is the GPU is sort of held in place with this mechanism here which we can release with this and it's also obviously plugged into the motherboard so on two sides on the third side it is held in place with these so unscrew these bolts so if it is easier we can make it stand that  We can't remove those because it is very difficult to maneuver through that. I think it's better if it's on the side.  That's why I'm saying it is very difficult to move this. So we are going to try and remove the whole frame altogether. Let's just move these bolts.  I see that the frame is able to move but it is obviously locked  So I think now what we can do is I will pull on this. So this is detached and you need to lift it up properly. Okay.  This comes off, but it's attached at the bottom.  you  And then attach some rolls.  Thank you.  and this is the CPU so what we can do is we can detach these bubbles which are sort of plugged into the motherboard and we will be able to release this so this is the frame outside and this is the CPU itself so we have to detach the frame yeah  The hole? The battery?  This is the lock. If you push the lock it will come out.  This one as well? Yes. All the external cables we can remove. The ones which are within the motherboard. So these as well?  Do you press the sides on this?  and release it and this thing also is fit so there's nothing to release but this is jammed so you just pull this out yeah let's just see yeah same with this so this is given yeah and these are the data cables  from the quick unit.  I think it's missing. All right. I think that this is something close."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_2_411_3010_1_480.mp4",
        "transcript": " Mm-hmm. Just lift it or? Mm-hmm.  Okay, mine's too big. I have a 14. This is 15. That's bigger.  Do you take the screw out all the way or just? No, but if the rods are already detached, I mean like this. Do I have to take this screw out? Yeah, I mean those parts you also have to separate. Are they? Yeah, no, that was the question if I have to take the whole screw out of this.  Do you want to use this one?  Mm-hmm.  Okay."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_2_451_1601_1_480.mp4",
        "transcript": " These should be the same size as them. This was a bigger one. Then maybe you can do the wheels or this one? No.  maybe there are more allen keys in the in the no i think we just have to remove this here but maybe there's more allen keys in the oh okay  Oh, I'm doing these. I don't know. Or I could just remove that. And I'll put this back.  No. This one's fine. Yeah? Yeah.  Thank you.  Okay.  I think so. Awesome."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_16_411_1110_1_480.mp4",
        "transcript": " Okay, so today we're going to disassemble this because the last time it was reassembled, a bunch of screws didn't have a place to go. So in order to find where it goes, we're going to disassemble the whole thing. And as you can see, these are all very, very loose. So first I think we can lift it onto the table.  Or maybe it's easier like this and then we just put the parts on the table. If we disassemble it here and then put the parts because otherwise it's so high. So maybe we take these two off first. Ah, the break.  So maybe we each take one of these off cause they're the same anyway. So these are whichever you want. And we first can take off the casings. So I'm just using the screwdriver to leverage it up.  Oh, sorry. I'm going to put that over here. And then I can start. I'm going to start with this screw right here. By rotating. Yeah.  Oh, I think I know why, though. Because this part is not supposed to be there, I think. Although we can fix that later. Oh, my God. Yeah, I got it.  Okay, so I'm just rotating the screwdriver counterclockwise. Add the Allen key. There we go. Now this part is off, and I'm going to put this over here and store it like this so I remember where each part goes. Now I'm going to take this out. I don't think this is how it was built before, but  And now again, going counterclockwise, I can unscrew this screw. Where did that come from though? But this was, this was like, what? Oh.  And now I'm going to unscrew this screw by again going counterclockwise with this Allen key. And I'm going to store that here. And I'm going to take these at the bottom off by again rotating the Allen key counterclockwise. So first with the short end and then with the long end.  You remember the shape, right? Yes. Mostly. So now I've taken this part off. I'll do the same on the other side. Again, rotating the Allen key counterclockwise.  Does it go in? Yeah, we could. Oh, perfect. Maybe the table would have been that bad. Oh, well. So now I'm just going to take this screw out. Thank you.  and then store this over here. And now we can move on to the plate. So I'm going to just unscrew these screws going counterclockwise with the Allen key. This one as well.  And the last screw again, rotating the allen key clockwise. And then now I can take this plate off. Okay. Now we have to take this part off.  Just get the casings off again, ugh.  And also this one. Okay, and now this part has a bigger, bigger, bigger... Where did we put it? No, no, I got like... There was a black one, this one, that fit. So...  Okay. Then I'll start on the bottom here. So I'm going to take this bracket off by taking out these screws. Again, rotating counterclockwise. And these also have these kind of plates in them.  I'm just gonna put these all together over here. And then I'm also going to take off this part. Going counterclockwise. It's clockwise.  Yeah. No, this is counterclockwise. Am I stupid? Or maybe wait, let me just, cause no. No, cause  Yeah. OK, thank you.  and then i'll store this here this here and we'll put this over here i'm also going to just put the extra screws over here  Okay. Do we need to disassemble this as well? Yeah. Okay. So in order to do that, I'm going to stand this up so that I can look at the screw in there.  It's kind of complicated. Yeah. I can't get it out. Okay. But this is also not loose. Oh, it's also down here.  Huh? Hmm.  Maybe because we know that nothing is wrong with this anyway. Like this is stable. We can just leave it. So I'm just going to put, huh? Yes. I'm just going to screw that back in by rotating the allen key clockwise.  The same goes for down here. I think we can put it down to get better. Oh, it's almost fine. Okay.  But I think now we're done. We've disassembled all of this and then we're gonna see where the missing screws go."
    },
    {
        "category": "disassembly",
        "name": "User_15_User_17_410_2210_1_480.mp4",
        "transcript": " So today we're going to... Oh, we don't need to narrate. I don't think. I think it said that in the...  Maybe you go on this side and I do this side. Yeah, so those two and those two you need. So those two, if you go on this side and then we just take this one off first.  Did you get them? Okay. Maybe we can do that together. There we go. And then it said to remove something with an Allen key, which is maybe these or what does it say on the  Okay, so this one, yeah. You need the big one, I think. Yes, and then I'll get the electric drill.  That was the wrong direction. It's still the wrong direction. I don't know. Oh, it's because I have to turn this over to screw.  I don't know how it works. Maybe this makes a difference. It's not turning properly. Now it is. It's not turning though.  Okay, there's one. Why is it not working? Yeah. I don't understand why it's not working. We can try the other side.  Maybe I'll try the other one again. Oh, this is open now.  I think so. But it's not turning. Maybe you try. I'll hold it.  Maybe we can find a screw to everyone. Did you get it? No.  Maybe we can just use this as a screwdriver, kind of. Is there a screwdriver? Well, no, but I think maybe we could... Yeah, I would just use this. The problem is the red part turns. I can't really grip onto it. Sometimes there's a screwdriver that you can use.  and plug that into kind of, um, and maybe we can just try again.  Do you know what this means at the top? Can I maybe try? Why is it not turning though? That's what I don't understand. Because like this it turns.  Maybe this screw's too tight. It's not turning at all. Maybe we can use it like this. Oh wait, that's the wrong direction. This direction. I think so. Maybe now? Yeah.  Okay, where did you put the other ones? Okay, now we can take this apart, I think. Yeah, just pull on that.  Okay, and now we can lay these down, I think, and then take off the legs at the bottom.  Okay. So I'm gonna put this...  These... Okay, I think... I think we're done. Already did that? Oh."
    },
    {
        "category": "disassembly",
        "name": "User_16_410_0110_1_480.mp4",
        "transcript": " OK, good. I'm going to start the light, turn on. And I'm going to disassemble this light using the screwdriver. I think it's too small.  put it away screwdriver to remove the screw and hold the nuts  remove everything first and then this one  It's going off. I need to remember this way is going this way. And the next. Keep going.  They are identical, and this is longer.  I will remove this part and next I am capping the screw Dissemble that like this, keep going  And to remember, the short is inside, the longer side is outside. Next, take the light bulb out. Dissemble this screw.  And next this one.  Great. Take out. Next. Send that apart.  Next, there are two screws. We need to hold the nut inside. Screw it.  And the next one, same.  And it goes out. Great. Now everything is to save. Dissemble.  Next, I'm going to resemble it back. It's not going to be easy. Let's see. Just hold the nut.  ok ok  this is help me to put the put it back  I will deal with it later. I will try one more time.  I need to get this. Let's go out of there. Great.  It's too hard. There must be another way. I'll try another way. It's so hard.  Flip back later. I'll try to do this thing.  I didn't think. There must be another way. I'll use my old way.  Great, that's all. And to the next one.  uh...  I don't remember what is that. I forgot about that.  Next.  I'm going to stop recording for a while and look how the light bulb looks like. Let's figure it out."
    },
    {
        "category": "disassembly",
        "name": "User_16_410_0411_1_480.mp4",
        "transcript": " Yep, start it."
    },
    {
        "category": "disassembly",
        "name": "User_16_410_2110_1_480.mp4",
        "transcript": " okay started I'm going to disable this computer unit first to cut the zip ties with this knife careful put it out put it away and next remove this wooden plate with screwdriver  remove the screw this one this side there  Next we can remove from the wooden plate.  Next, remove the bottom connect plate, which should be from the downside. It's from the downside. So flip it. Using the smaller. Yes. First.  the last one left this row move properly  OK, so this connection part is removed. And then from the other side. Coming out.  good another part is out next we should remove the side place which is this part anti-clockwise  this part now this can be removed  but first we have to remove the green power connection which is this part by using this screwdriver which is removed not yet more  plug out and remove the plate which is removed put them here put them here and next remove the top plate  top plate remove the plate there are four screws from which is the top side  The top is removed. Also remove the bottom.  And next, remove the REM chip. The REM chip should be this one. It's removed. Disattach the hard desk power cable.  Looseness.  Hmm.  I believe I need to unscrew this. This should be the hard desk drive. Hard desk power table cable.  cpu  Oh, is this cable able to be removed? Let me see.  Scroll them back in for a second.  So, small question. Which is the hard disk power cable? If you flip this. This is the hard disk. Oh, right. Right. Thank you. I must screw it in. Make sure this part doesn't drop. Good.  Move this cable. Remove the hard disk. Oh, this one. OK. Thank you. Remove these screws.  This console."
    },
    {
        "category": "disassembly",
        "name": "User_16_411_2310_1_480.mp4",
        "transcript": " Okay, start. Disassemble this lamp. First, unscrew the bolt from this upper hinge triangle plate. This is the number one. Hold the nuts from behind.  and number two is here all the knots from dropped  And then, use hand twist to unscrew this number three bolt. And this going out.  Use the screwdriver. Use it.  white in the middle yes  like this and then remove  this part and for the unhawk the springs this is the spring unhawk the spring this is for the upper part this is number four unhawk the spring yep  remove it and unscrew the spring hose it's unscrewed and also this one and remove the bolts one two three this is the number one from the longer side  Number two from the short side. Sorry. Hold the nuts. Yeah, that's right. So number four. Hold the nuts, right. Right. And then remove it.  Remove every part. This is the middle part. This way. And then remove the spring from the lower part. It doesn't have a hub.  And store everything here. And the floor hinge. Unlock the spring. Unscrew the bolt number two. This should be the number two. Yes. There's one and hold the. Hold the nuts as well.  Then everything is removed the upper part middle part and the lower part"
    },
    {
        "category": "disassembly",
        "name": "User_16_414_2101_1_480.mp4",
        "transcript": " Okay, I want to disassemble this table. So the first, put on clothes.  Empty the table. So this is not removable. This is empty. Next, mark the side of the wooden desk. How should it be aligned with... So, first, we need to mark down. Like this.  3 location  then unscrew the bolt unscrew the screws holding the desk which we are going to use screwdriver so here is one bolt unscrew them  first next is here okay this is the second one  And away here also.  Why not? This side is another one.  And there is no... Okay, so I took it out. This bolt is unscrewed. So we have together three. Next, remove the desk. Use a blanket and place the desk on it. Put a blanket on the ground.  Okay, adjust the crank, which makes the table a crank. This is the adjustable table. So we attach the crank to adjust the table to the lowest level.  Use clockwise to adjust the table to the lowest height. Okay. We reach the lowest height. Put the crank away. Next. Remove the crank. Unscrew the 6 bolt. Remove the lower plate.  For that, we're going to use the Lanon key. I guess we're going to use this side. That's great.  smaller size bolt second bolt third bolt another side also three  put them together take the lower case off and then remove the upper case  use the larger allen key unscrew the bolts  So.  Last one. The uppercase can be taken off. Can be removed.  Upper case, lower case. Then... We have to remove the bolts holding two ends.  which is from the inner side of these two yes, okay gonna remove this one  So here. Two. As well as here. One. Two.  Okay, I think I can separate them. Okay, this is separated. Lay down both of them. Then here's the drilling machine.  Outer bolt, which is this one. Find the appropriate growth. Yes, this one fits.  a little bit a little bit small maybe find a bigger size this might be fit it's too big try this one yeah this one's good  Take out the drilling head. Take out the drilling bit connection part. Connect to the drilling machine. Okay. Good.  removed remove another bolt bolt has turned this seems not able to  remove so lay down so here both on top  cannot be moved so lay down the leg separate two legs lay the legs down horizontally which looks like so it should be looks like this  Okay, sort the bolts, make them together. Sort the bolts, make them together, into upper, 6 lower. Okay, this is the connection part, put it in the middle.  I'll screw the black bolt, connection the base and feet. This is the white bolt.  Use the white bolts. Loose them first. And remove each bolt.  removed so the feet and the leg is removed so as here first loose the bolt and then remove the bolts put them together  So the leg and feet are separated. Sort every bolt and make them together. And sort the tools.  Put the tool back. Got the drilling bits. Let's attach the power. Put the drilling bits back to the drilling bit box.  Close the box. And this is every part of the table. Disattach and remove the gloves. Finished."
    },
    {
        "category": "disassembly",
        "name": "User_16_451_2001_1_480.mp4",
        "transcript": " Okay, now I'm going to disassembly this trolley. First of all, I'm going to put the gloves on. Put down another one. And put the toolbox away. Here, first of all.  search for tools this is all the tools I might need so first I use this one first  remove the vertical bar so this is the vertical bar need to be removed  remove the power loosen the bolt it's removed hide away  Let's remove this one one more time. Yep, that's removed. Now loosen this. Put it aside.  First, the vertical bar is removed. And then, I have to remove the base plate, which is this plate. For which I need this allen key. Remove each board.  break the trolley avoid the movement remove the bolts one by one remove remove this bolt  another side remove this bolt I'll fasten and remove  this plate is removed another one I'll fasten loose this bolt and remove the bolt I'll fasten the bolt and remove the bolt  So put the bolt together and remove the base plate. Loose this bolt.  remove the bolt, loose the bolt remove the bolt  use the bolt and remove the bolt now we need to put every bolt together and remove the plate now we need to disattach the four wheels  first we need to turn this down and use the bigger size of island key to remove the well remove one of them  put it away next  too much further and next next  remove the bolt remove the wheel the wheel is removed and next disassemble the connection of the wheel  different size of the allen key the connection part is removed next  next wire connection part remove the bolt by removing the bolt you need to use the allen key  put them together next another wheel connection part unfasten loose the bolt put them together  In the next movement, we need to remove the individual part and remove the horizontal bar. Turn it around. Remove this horizontal bar. We need to unfasten this to  Smaller sides.  put them together next remove the frame loose the bolt loose the bolt  Loose the bolt. Loose the bolt. This bar will be removed. Loose the bolt.  And also remove this part.  so that each part is removed the frame is also removed put them, sort them together  This is the wheels, the base, and the frame and the vertical and horizontal bar. And sort the tools. OK.  Now this assembly task is finished."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_1_411_2210_1_480.mp4",
        "transcript": " Here are some instructions for dissembling the table. First we have to put down the gloves.  And just adjust the crank at the lowest level of the table. Unscrew the six bolts and remove the lower plate, this one. I think we need to use  I mean, yes, I think it's a small one, I think. Remove.  Okay, put it off.  the six onto the plate and i'll remove the cram sure and unscrew the eight black bolt and use the bigger  Okay.  I think we're going to give it a little bit more.  And then we remove the bolt holding two ends of the connection rod from the inside. OK. This works well. So maybe this one.  Bye.  Then we need to take out these from the drilling machine. I'll find the drilling head.  6, maybe this. That's OK.  Put it on the connector.  Okay. Okay. Hold it. I'll try and unscrew this. Set it to low. Okay.  removed. Now we can, oh, this also. Okay.  And separate the two legs. We should be able to pull them out. This is locked here. Oh, this is locked. Okay. I think last time. Yeah. All right.  And lay the two horizontally. Unscrew the bottom. I think this should be this one. I can use here. I may need this one.  OK. OK.  He is removed  four i'll put inside in case this uh from the the uh just just from the here from the top okay good should i store them separately  I'll also put it here I'll put the tool back and I think we can finish disassemble"
    },
    {
        "category": "disassembly",
        "name": "User_16_User_1_411_3010_1_480.mp4",
        "transcript": " Disassemble this table. Clear the table and put on the gloves. Disconnect the wooden plate.  and remove the old tray and next detach two hangers using this to detach this  inside and the four corners disconnected using the winch  One more removed. This kind of removed from the... Is that it? Yeah.  All right. Yeah. Okay.  There's some problem with this bolt. The foot is over there.  and then next detach the central bar by using the allen key  put this in the sidebar also yes sidebar  Okay, let me know.  Move it up here.  It's finished. Remove the gloves."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_1_451_0701_1_480.mp4",
        "transcript": " First I think we do put the gloves on. Yes.  Let's see which Allen key fits. It's a bigger size one. It should be this. Let's see, these two fits, I think. We need to remove this bar first. What does it? This is far from there.  now we remove the cover it works  this thing.  removed we need to clean it first or the floor no to clean the board first no after we remove the frame  Thanks.  I can hold it. I can hold it.  Okay. I'm going to use the large one. Oh, okay.  Yeah, thank you.  You want to remove this?  Thank you.  Okay, now...  Yeah.  Thank you."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_2_410_1010_1_480.mp4",
        "transcript": " Okay, so what we want to do is fix this assembly stand and this  to disassemble it. And you can just start with the element piece. For the bigger one? Yeah, the bigger one. And I'll fix the... Remove the corner piece here to take this off first. Okay. Fix the... Make it stable.  Yeah, let's maybe start with... Okay, sure. Oh, yeah. If this is in the way, we can... It's a bit hard. Okay. Just leave it on this side. Okay.  Okay, then we can maybe start with removing those.  boost another one did you also remove the one here? yes but not fully removed fully remove this  Hold it. Oh, it's your hand. Okay, wait a second. It's not fully. Be careful. I will check it out.  put it back remove the top or remove this I think remove yeah okay just like the other one  It's very hard.  No. There's something else inside? Okay, let's maybe just remove the bar. Yeah. Oops.  I hold it. Okay, it's removed. Hmm. Hmm.  Can I remove its head or with a small inch?  it's still not movable  It's a little bit tight. It's not removable. So I can't move it up and push it down? No. No.  something oh yeah there is one more like something like this inside okay um then how can you move this now can this push up no right no it's very tight  Rotate? No, also no. Is that removable? Maybe we can try.  We can look in the room.  It's too small, it's too big.  The same one? No, it's smaller. I think it's too small. You can just try it. It's too big. Okay.  Yeah, it can be removed. Okay. Okay, perfect. Then maybe try the one... What is this? Yeah. Oh, great. Something dropped. No problem. Okay, so there's the center in the center.  It's cracked.  Is it loose? You can just remove it completely. Anyway, you just leave it in. But this one you also just left. But yeah, this is also one of you. Oh, okay. Maybe you can do this. Oh.  Can you take the key and try to get this small thing out? Or you can just slide off the bar.  Or maybe, okay, maybe you can hold this and I take off the covers. Okay. Or like, slowly. Oh yeah, okay. Hold it. Hold it.  So these two things, it's like doing this and... Are they different? No, no, no. I mean inside of this, it's like this. Yeah. Okay. So now we can remove this from the panel. The last part. First, yeah, let's take off the covers of the bars. Yeah, sure.  I think you need to like doing this. It's too big. And how it's hot, the lever. Yeah. And this way. I can start.  I think here's a, you don't want it to break. Maybe we just rotate it to a side. No, no, another side, like this. There's another waste free to slide off.  Good. You have it? Yeah. Okay, so now what we're going to do is add one more piece on every side.  like two fixing parts of this assembly so it won't rotate anymore I think remove the something stopped here but first remove this must be done and then I think it can rotate it you rotate I push it  And I think if you want to put one screw inside, we have to remove one bar first. Oh, yeah. And then slide it. Yes. Or maybe we can even take those screws. Sorry. It could be. No. We'll have to remove one of them. OK. What about the smaller screw here?  It's too small. Okay. Maybe we can use something like this. No, it's too difficult. This one is good. This one is also long. Maybe we need a bit longer. It can fit. Good. Oh, great.  Which one? This one? I think we have to remove one side of the bar  So this one is a bigger one. I only have...  so we can or just take take the bigger one from here take this this should be the bigger one but we will need those to like reassemble all right right right so i'm just gonna maybe take a small  I'll try to make them the length is the same I'm not sure if that's useful but  I think, I don't know. Mine is maybe a bit too long. So it won't fit in there. Yes, you're right. So long. Need another screw maybe. This one? Too short?  Okay, let's see. Just a little bit. I think it could work, yeah? Mm-hmm. We could have a try.  Put another bar back.  notice yeah okay now we can slide it on  Maybe let's do one side first. Yeah. I think this part was too much. Let me try if it can be fixed. Kind of stuck? Yeah. I'll lose a little bit. Then we can put it aside and I'll screw it out. Can you do it by hand?  I think I can do it by hand. Try to hold the screw inside. Yes, that's it? Yes. Okay, and the other one? Another one.  I'll hold it.  Okay. Yeah.  Maybe you can, there is a hole in the middle. Maybe if it's too long, you can take it into this middle hole.  I mean, I'm not sure what's your situation. Let me try it. Maybe you can try this side, yes. This side is a bit harder. Let's get it in. Let me try if I can.  This is weird.  Do we have another way? Let me think. Do we have another way to do this? Was the problem that this was too short?  I mean there has to be space for the metal here I think it's not too short because this one is the original one and if this fits that one is longer  I can see. If I use hammer, do we have a hammer or something? It goes in there.  Okay, you can, maybe a little bit. It's too close to each other.  Why is it too tight? Close the door first.  take the scissor and hold oh yeah a little bit yeah okay great i can hold the scissors  I think this is even enough. Okay. Yeah. So I think this should work now. Just have to watch how to react. Or we light it down. Light it down. Light this card down. Let's try first. Okay. Like this. Maybe another way. Like this. This way. Okay.  Yes, one is in another.  We have to draw this way. It's in how many millimeters from here and something. It doesn't fit like this.  I think it fits.  I think we'll have to move a little bit to the right. I think we'll have to move it a little bit like this.  Yep.  No, let's put it out and we, I think we can do this, do a measurement like from, from this side of which, which, which millimeter from this side and starting from the same position or if not, it will be like not alive. Do we have a pen or something?  Starting with this point and  roughly very roughly oh this problem might be oh this is the original one right yeah but now they're like kind of the same right  make a curve it's 31 starting with this align with this side try again  They are going inside very easily. Yeah, mine's also in. Yeah, going inside? Great. No way. Oh. Yeah. They're moving. Just push it down? Uh-huh. Is yours in? Oh, yeah. You're stuck?  Can you push it in? I can go inside now. Yeah, this is pretty, yeah. Minus, that could be tight again.  Okay, yeah. Yeah? Yeah. Great. Can you push it down? Mm-hmm. It's also hard. Mm-hmm. Sorry. No problem. I hold my side. Yeah.  Yeah, you can find another screw.  Is, I mean, the thing will stop rotating if we have, like, only... No, only one side. Yeah, that's possible. Yeah. So, maybe let's just do this. Yeah, sure. Let's try if this light down will be better or not. Okay. It seems not. I cannot see my...  Your side can be aligned to the right, very right. That could be easy to position in. Second.  Yep.  Wait a second. You can put this in there, here. All the stuff over here. Can we put it out? I can leave this through there.  No, we can put it on the other side. Right. Yes. Yeah. We can level it, put it in here and another thing goes down.  Yeah, but I mean the rotating thing is in the middle here. Must be in the middle? Yeah. Must be? Yeah. Okay. Let's put it. I mean, no problem. Let's do it again. Yeah. Let me see how can it be. Oh, okay. Let's put it out.  No, not yet, I'll wait in here  Okay. And push it down. Great. Just leave it here first. Yeah. And is that possible? Yeah, great. Yeah, that's possible. But now it cannot rotate anymore. Okay. Just a little bit. Yeah. Just leave it like that. Yeah.  The rest part?"
    },
    {
        "category": "disassembly",
        "name": "User_16_User_2_411_2510_1_480.mp4",
        "transcript": " to disassemble this table move everything away move the computer  I think we can use some to  Sounds hurt. Horrible sound.  This one's too small. Are they different? It's different? These are 12. Oh, 14.  Okay, now. Another side? That's very tight.  How should they attach with each other?  oh hold it in case they drop  You can use mine, I'm finished. Oh, this one is the same. Oh. This one is a 13, oh wow, 13 or 12. That's weird. I'm using 14, so. Okay.  and i think we can lay it down or just  Thank you.  We have different? Are we the same? Same? Okay, so I'm out. Thank you. Now we can...  lose this part two legs okay  that's it finish recording"
    },
    {
        "category": "disassembly",
        "name": "User_16_User_2_451_0602_1_480.mp4",
        "transcript": " Okay, we're going to disassemble this.  down the computer. Let me check which way. This way, right? Okay. Okay. Let's open this. Okay. Let's try to figure out where to open. It's here? Okay. All right.  away so this is our pc so we can start with a chip rack and so this one yeah it feels like it's like the lever you can pull this one this one just pull it to the side oh okay  this is the dust also the pull this is the fan one I'll screw them  The last one. The keyboard disconnect. It's a button. Oh yes.  Okay, the fan is out. This one? Okay. GPU frame. And then we have to take out the whole thing. Okay. So, oh, the bigger frame. Okay. All right. I'm going to remove the bolts for the one.  Same side.  last one out and then disattach all the cables I think that's it pull it out just a little bit  Oh, here is one more bolt. Now we can put it out. Okay, it's out.  GPU card. And then the HDDs here. Just detach all the cables. Okay. They're out. Just leave the cables and then just use those. Okay.  Okay. Out. So slow. Okay. Hard drive. I am...  Then this heatsink, because underneath is the... This is you. Loose them.  Mm-hmm."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_14_407_1712_1_480.mp4",
        "transcript": " Okay. So, to put on the gloves. There is one more glove. Put them on. And before everything, we need to find a tool. Okay. We need this or we don't? Just try it.  so first we need to remove this bar  Okay, then we need to... Okay, looking for... Yes. Can I have that one? Yeah, the same? Yeah. Okay, sorry. Remove those bolts. Okay, we'll go there.  you don't need to charge your glass so this tool says not use it  can be moved  Can you also remove this one?  remove this middle one  Thank you.  and remove the frame  Next. Oh, OK.  I don't...  And do we need to remove this? No. Put every tool back. So we're finished disassembling.  I'm sorry.  and next  You want to sort them? Yeah. Okay. Take out the clothes and finished."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_14_412_0402_1_480.mp4",
        "transcript": " I'm gonna teach you how to disassemble this camera settings. First, pick up the proper tools. Let's check if that's okay for this. Yes, you're okay? Yeah. Yeah, so first step, we take off this connection. It's like this. Lift this up. No, no, no, see me. Lift this up.  Yeah, and pull it out. Yes. And next, turn this around. And so there are small bolts. We need to... Yes, remove the small. Yes. I will do it first. You can see. Just remove it.  Be careful, you can hold the hammer, yeah.  Next, put them together. Don't get lost. And next, we disable these bigger screws using the proper Allen key.  see so this is facing this side put them together next remove this connecting bars using the same tool be careful  Be careful. So just remember this is facing this side. Yes. And don't remove this also.  Okay, it's all removed. Okay, now remove this, this, the upper one. Okay.  Do you have to put the arm in here? Yeah.  yeah after that remove baseball inside yes yes a little bit hard is that able to a little bit hard  Okay. It's hard for me as well, so I gotta wait till I can miss this. Okay.  Now, all of them are removed. Sort them. And finished. Put this key back also in here."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_14_412_1510_1_480.mp4",
        "transcript": " okay so in this task we are going to use some tools for screwdrivers observation there's also some screwdrivers different pick up some tools from here  different screwdrivers you can try if that feeds that one is fact I think yeah that feeds it's too small or you can use this also I'm gonna use the smaller one  Sure, and yes, remove the screws. So first, I guess we should start from here. Yeah, sure, we can take out the lamp, the light bulb.  No, I'll actually remove the... Yeah, sure, we can remove the ball. Light ball. So first we are going to remove this ball. Yeah. It's coming out. You can put it over there.  Sure. And this one shape, we can use some different tools like this. Remove here. This cannot be removed. This cannot be? Yeah. Just remove these screws over here. Okay. Yeah. Sure. Remove them. You can use this screwdriver. Oh, yeah. It's the same. Make sure I can use this. It would be easier to.  the screws are removed and the next one this is also removed and next with my hand to remove this put them together and remove this triangle shape also from the back side  and this thing is de facto I think it's dropped out it's broken so I'll put it aside so this small  Okay, let's check if we can remove anything from here. It's a big screw. It's not easy to remove. Let's start with some other part. First I think remove this spring. Put them on the side. Also here.  I'm going to remove this bar by using this screw.  this is removed here okay  Remove all the springs together. Do you know if you can remove this part? Yeah, I think you can just with your hand. I'll try it. It's very hard? Yeah.  It's very tight. Maybe it's not able to remove. I'll just remove this one over here. Sure, I'll try to. Maybe it can be pushed out. No, it's not able to put. It's not broken yet.  Is there any screw here? Let me see. I cannot see over there. No, it doesn't have a screw, but it's stuck. Because this cannot be removed, so that's more easy. Let's just turn it around and put it out. Okay, this part is also removed. Next, we can remove the bottom part. Let's remember the shape. Just this shape.  Okay, I'll use the screwdriver to remove the screw. So I can see you're tightening it. No, no, no. I'll remove it.  No, these two parts are moving at the same time simultaneously. If I hold that, another part, it will be removed. And we can move this part, also this part. This coming to here, yes.  put them inside in case we don't want to lose them so now you can see the lamp is complete it's on the left oh i can hold you please thank you okay  remove this part and now every part is removed except this one this one is not able to move two sides stable  okay let's see if the air can remove no no there's a big screw inside so we can see the lamp is already been disassembled completely okay let's stop the recording"
    },
    {
        "category": "disassembly",
        "name": "User_16_User_14_451_1102_1_480.mp4",
        "transcript": " okay now we are going to disassemble this pc so first put on the gloves i will gonna teach you how to do it so you put on the gloves now open the pc open the hinge open the door yes let's just open it  you can try how to it's not locked so you just open it  Yes, like push to there a little bit. Yeah, I'm going to try it. I'm going to try to slide a little bit.  I think you should press this and try it and try some like a slide or just open it.  now check everything inspect a little bit and now remove the chip rack which is this part and you can  Lift it, I think it can be like this and lift all of them So this part and also remove  let's check the fan yeah the fan also inside so it's removed together so we now remove the dot so this part and you will here just lift it yes there are click you have to check there just lift it and try to  yes and it's removed so now we need to remove the fan so this is the fan we have to remove it by yes by unscrew the bolts here's the screwdriver screwdriver  screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver screwdriver  And so remove all of them.  okay so before you remove it you should disconnect the wire this one the wire connected to the motherboard disconnect it yes and remove the fan you can so the fan is removed  so now so this is the cpu cooling so we have to before we remove the cpu we have to remove the the cooling part so remove yes and remove the bolts remove the bolts yes okay  It doesn't need to be disconnected. It doesn't need to be removed. Also, there are also two behind. Remove, remove.  So the cooling part is removed and put it away here or there.  and next there are four bolts for the CPU so using the proper screwdriver to remove the bolts also yes this one the correct one  yes the cover case of the CPU is removed now softly remove the CPU the big one is the CPU the chip yes gently removed the whole thing gently  and now we have to disconnect the cable of the GPU and all of them just here  To remove the GPU part, they also have bolts, so you have to remove the bolts to connect into the bolts. Using the appropriate screwdriver.  Yes, remove all of them. All of them? All of them, yes.  yes they are in the frame  tickle time tickle time tickle time and all balls are removed  carefully store the bolts now, disattach the connection to the motherboard just lift it a little bit just a little bit will be fine and here also, it will help you with it  Just a little, just a little, don't, don't, too hard, don't, not that hard. So now you can take the part, remove the... Is all bolt removed? No, there is one. Oh, okay, okay, then remove this.  now remove this gently, softly, slowly, carefully lift this frame take this  So the GPUs are removed. And now we have to disattach the cable of the HHDs. The cables.  all of them the power cable and the data cable cable all of them yeah all of them and now remove them just take them out just like no no no the hhts yes  Just press it, press it into together. Press them together like this. Yes, there it is. And lift.  You can see here, it's inside, so just like this, and here also, just press them. Yes, it's pretty simple. Yes, all of them. Yes.  So if it's not stuck, just shake it, move a little bit, will be coming out. So this two, this also, this two also. These two? Yes.  so now I'm going to remove the cable to the motherboard all cable you can see like this this the orange one the cable one yes and also this little white one  yeah and i think there is one more you have to remove gently okay so the cables are removed this we do it later so now we remove the ram  by pressing the bottom here also the left one and the second one also press them first now we are going to remove the heat sink the heat sink  heat sink ah yes it's already removed by the so we're going to yes no no this one this is the one yeah so we are going to remove the battery and suppress that the gold one or you can use the screwdriver yes screwdriver but be gently simus battery yes  you can use the screwdriver don't break it just press the gold a little bit softly and you will find out how to remove that don't break it  It's not coming off. Just, you can see that here is stuck. So just press it and it's going, it's off right now. You can just take it off. I just press it and I just take it off. It's in again. So you can just take out the gloves and press the golden  like a button thing or some stuck thing just press it and it will go and now let's see which cable we can disconnect it so you can you can disconnect the data cable the blue one yes this for blue one  okay also this one oh it's already okay so now we disconnected most cables now let's sort the parts put them together and what  Okay, that's it."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_14_451_2901_1_480.mp4",
        "transcript": " started okay so now we are going to do this disassembly task and i will teach you how to do it first we think we should put the gloves on and next this is all tools we need so first  we need to check out the instruction letters we have to remove this bar and you can looking for which suitable for this which allen keys the sizes should i use this one? yes these are allen keys  I'll hold it for you.  okay it's different size  the vertical bar is disassembled I will put it here  I think you can continue with this, yes. I can help you with this one.  Next, the vertical bar is disassembled. We need to remove this plate.  Thank you.  I can help you with this side  no it doesn't fit so it's only one continue loose the bolts okay now we loose all the bolts we can put the base plate here no no no it's already loose so  put the base here and this one here you can like this way like this way okay next we are going to detach four wheels but first we need to turn this around  You can find the suitable Allen key to remove the wheel.  You can continue with next wheel.  And I can help you with this.  okay and next when you remove this wheels you have to remove this individual bar part and I will find the sweet bowl allen key not this one is this? that fits? okay this one fits  I will first remove this part. Okay. Remove this.  Okay, now we turn this. Now we remove this bar, the middle. You can find the sweet bulb, Allen key for this bulb. Allen key, Allen key. Allen key? I think this is true. It's here?  no no elenkey elenkey elenkey is not screwdriver so this is the elenkey bolt because  oh you gonna hold hold oh okay no loose yes this way anti-clockwise this is video  Another way, this way. And now turn this around. Okay.  Also this one, we have to remove the vertical bar. It's removed.  Now we are going to remove this frame, this edges, the same thing.  You can just lose it. And it doesn't need to be fully out. Just lose it. And you can continue. Continue with here, I think.  yes it's loose now we turn it back i can i can finish this for you  No, this is completely  we will sort everything together we can wipe it and first we can sort the bolts there are the frames  Okay, thank you. And you can clean the, wipe it. I'll hold it for you. Do we have a spray? No, we don't have spray. We can just wipe it. Yes. Here.  Now the disassemble task is finished. I can take off the gloves.  Okay."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_15_411_1110_1_480.mp4",
        "transcript": " have a place to go. So in order to find where it goes, we've got to disassemble the whole thing. And as you can see, it's a little bit loose. They're all very, very loose. So first, I think we can lift it onto the table. Yes. I can use this up a little bit.  What do you mean? If we disassemble it here. Oh, yeah, sure. That makes sense. So maybe we take these two off first. Is that able to break? Yeah, sure. Maybe we each take one of these off because they're the same. Sure. The same.  So I'm just using screwdriver to leverage it up. Sorry, no problem.  I'm going to start with this screw right here. Why it's so loose? Every part is so loose. Oh, I think I know why though. Because this part is not supposed to be there. Oh, it's not fixed. It's not supposed to be there. Oh, okay. We can fix that later.  I'm going to use my hand to put it out.  yeah i don't know why why it's like a  Continue this part. You remember the shape, right? The shape of the things, right? Mostly. Now I've taken this part.  Do you need this get higher? I think it can go higher. I think it's much easier. Careful.  Thank you. No problem. And then we'll start this. And now we can move on to the plate. A second.  Oh, okay. There's another plate. Now we have to take this part off. Yeah.  Mine are too tight. I will find another tool. This could be easier. It's coming off. Okay, now this part. Start from the small one. Not this one? No. Okay.  Okay. Okay, great. I will do it.  Not very fast. And then I'm also going to take off this part. You need to hold it?  I think it's the wrong way. I think it should be. Oh, go another like this. Oh, it's coming off. Okay. Oh, careful.  Yeah. No problem.  yeah sure we can disassemble everything and  Okay. No, it's just landed there. Okay.  yeah it's too small to roll it maybe because we know that nothing is wrong with this anyway like this is stable we can just leave it screw it back in screw it back in okay sure  Yeah, I think we can put it down. We can better. Okay. Other way around. Other way? Okay. Ah, okay.  Mm-hmm. Mm-hmm.  Am I recording now? I think you are, yes. Okay. Okay."
    },
    {
        "category": "disassembly",
        "name": "User_16_User_17_410_1410_1_480.mp4",
        "transcript": " So we are going to assemble a table which is in room 414. Make it together and to put this to the table. 414.  put this aside and put it onto the doorway open the door and then push it back  going back to room 410  we can put it yes we can just put it on the ground out of the trolley and now move the trolley aside and to disassemble the table we can put on the gloves let's close the door for a second  the light is already on so we're going to disassemble this table by removing the screws we have smaller size and bigger size  1, 2, 3, 4, 1, 2, 3, 4, each side. So, let's find a screwdriver. You can use one for the, no, it's not the screwdriver, it's our shiplash. Using this one. And this one, try if this size fits. I'll try the smaller size.  Does it fit? Okay. Smaller side. It's a little bit too big. You can put it here.  it was too big so I'm gonna try to use some different tools to fix oh here is some different tools here is the fix screwed it out by anti-clockwise  put them on the table and send this back side one by one  You can be careful because it's going to fall out. Which part? This part. There's one. It's locked? Okay, good. We need to remove this. Yeah, sure. Oh, there's one more. You can see. This handle can be removed easily.  so i think we can lift it up  Let's remove this part also. Find a smaller size. If this fits, I'll try it. No, it's too big. I think it's too small. You can try, you can try. It's too small? Okay.  this one is too big look for from another room check from the toolbox  I'm going to check if this fits. These are similar. I'm going to check if these are similar. I'm going to check this too if this can fit.  Take this tool back to the room. Leave the room. Close the door. Enter the 410. We can check if this tool fits the size. Yes, mine fits. Let's remove this screw.  What about yours? This? Yeah. Removed. Put them in the different position. And the second one.  Removed. Third one. So it's all removed. OK, you can use my  You can use this one. This one, you can use this one. I'll put them together. Put this away.  Two, two.  It's removed. It's fallen now. Okay. Okay, I can hold it for you.  So, this part is out. I will put it aside. Try to remove this part. Lift it. Lift it. Put it out. No. It's coming out. Okay, good. Let's put it aside on the ground.  And what else? I think we can disassemble the leg by... We can let it down by this way.  yeah sure let's check here it's more screw yeah there's four use the suitable tool you can check yes if it's also anti-clockwise remove four parts  third tight ones out second one out third one out last one hold the leg  Last one out. Remove the leg. Put them aside. Let's remember it this way. Put it back for a while to remember the position.  And here is one more screw. How can we just move it? Just move it. One more is very tight. Also here is one more. We can remove it.  It's removed. What can this do? Nothing. Also, here is two more I saw. I see. You can see. This here? Yes. It's fixing this stick here. Yes. So without that.  maybe you can try it can be pulled out? no  So if we want to remove this part, we have to lose these screws. So we can try to remove this part. We can try with this.  It doesn't have this part. I'll try this part. It's pretty tight.  This little side is removed. Hold it. Uh-oh, hold it. Thank you. Good. This part is removed. It's loose, but it's not removed. Okay.  put it here if it's very oily okay let's try with this screw this like a star shape star shape looks very interesting  Let's try to find. Yeah, sure. Maybe. Oh, yeah. Here is a small tool. Thank you. Yeah. So this is the line. I'll try to find which one fits the star shape. Five, five, six. No, it's too big.  This is the right size for this. You can connect it to the table here. Give me this. I'll put them on.  Is that correct? Oh no, no. I think I have to connect with this, right? Yes, it's from bottom.  another way I do it clockwise you can hold this one out the second one  Okay, the second one also come out. I'll put it aside. Here, no, no, we need to... Also? Oh, yeah, sure, yeah. I think we can... No, we don't. We have to move the stick out first. Can you hold this, please? Thank you. I'll lose this one.  with my hand to do the last part thank you also the last part with my hand to do the last part with my hand it's out put the  No, still not. This little black part can be moved a little bit. Let's see. No, we can pull it apart now. Can you? No, no, no, it's from inside of this black one. But we can still pull it. Okay, sure, great.  I think it's a metal mesh. Can this part be removed or something? I think here the little black dot, maybe it can be  Opened, no, not pushed. I don't know. Yeah, you can just pull it off. Nope. Since it's stuck. Okay. Yeah. Yeah, because this part is to adjust the height using this tool.  So I think this, every part we can remove is removed. The other part is very fixed. This is some part looks like can be open or not.  Oh, I know this is the part connected to the downside because if we use this,  to move this it can automatically connect it to the height it can move together so if we move the this part is connected to the old leg you can see yeah but i didn't have a car like this because they are moving together so it's the same geometric okay i'll level it down to the lowest  I think it's the lowest. OK, great. Everything is disassembled. OK, should we stop it? Sure. I will stop the recording."
    },
    {
        "category": "disassembly",
        "name": "User_17_407_1510_2_480.mp4",
        "transcript": " So today we will disassemble this lamp. So we will remove all the screws on it with a screwdriver. So we will first remove the springs.  And next we will start in from the bottom and remove the screws.  Now we have to remove this part first. So the screw washer is out. So we can take out the screws.  and this plastic part first. So we can remove the swirls.  So we can remove the bottom part of the lamp. So this part is the upper side, this part is on the downside. And the middle part, we should remove the screw washer first.  Remove this. The same thing is fixed. No. We can screw a little bit. And we can remove this triangle.  So the upper part of the lamp  so this part is out and to get away this triangle first plastic triangle there's multiple parts here  a screw washer plastic another screw washer and this triangle the screw and the ladder another triangle here you cannot move this part  But the plastic part is okay. So we'll move this piano first. And screw for this direction a little bit.  And we can see the screws are out.  this is fixed so I should say we have complete disassemble this lamp  The rest parts are fixed to the stick. No. Actually, we can't pull it out.  So I think we finished."
    },
    {
        "category": "disassembly",
        "name": "User_17_410_0411_1_480.mp4",
        "transcript": " Thank you."
    },
    {
        "category": "disassembly",
        "name": "User_17_411_1610_3_480.mp4",
        "transcript": " so today we are going to assemble and assemble this metal frame first we have to get some screwdrivers so first we have to remove these three iron bars I wrote here we'll start with this  so we need another to remove this cover  the first cover and the second cover and these two  so we'll first move this and we'll start with the upper part with this screwdriver and we'll first remove this connector here and use the  Lose a scrolls bit. Now we have to take our gloves. It's a bit slippy.  So the first screw. So this part is down. Screws out.  And the bottom.  So the connector is off. There's another connector here. We'll lose the screws.  and for the bottom there are two connectors here  There's a screw washer  so this part is removed we place it here on the table and we're going to remove this part this time we'll still begin with the top remove these two connectors  we'll lift it up so we'll put the right part to the right side of the table and we'll put the left part on the left side of the table and continue with this small connector  and next is these two connectors  so next step we will remove this part here this part this road and there's two parts the short one and the long one we'll first remove them together from the bottom and we'll separate separate this after so  Yep, we'll remove this two connector.  The other one is here.  next we will separate these two we have to remove the cover here first remove this from the connector so we can loose the screws  Finally, we will remove this plate, this black plate, from the bottom, from the base. There are four screws here we have to loose.  and we can remove the plate so we now successfully reassemble the frame  And that's finished. And we'll take off our gloves."
    },
    {
        "category": "disassembly",
        "name": "User_17_411_2310_1_480.mp4",
        "transcript": " So today we're going to assemble this lamp. So first we have to get the right tool, get a screwdriver.  we'll see if it's the right one this is the right tool so for the assembly we first will start with the upper side  and we will first unscrew both one and two so make sure we are putting the lamp in the right direction towards this side so we will first unscrew  And there are school washers, so we'll put them aside.  we'll put the screws together with the screw washer and we'll use our hand to unscrew the third bolt  yep so that's the first part we remove the upper hinge and we put all the tools together and the second step is for the middle for the middle hinge  so we first we have to unhold the springs and the spring hooks so yep  and next we will unscrew these three screws put them with the screw washer together  so this is for the middle hinge  So the next step is for the lower hinge and we have to first unhook the springs.  this part is fixed so we will remove these screws and the screw washer  And use a hand to unscrew this part. And there's another screw washer here. So we pull  to this road here. We can install the lower hinge.  so now we finish disassembling the lamp"
    },
    {
        "category": "disassembly",
        "name": "User_17_412_2110_1_480.mp4",
        "transcript": " Okay. So today we will first assemble this computing unit. And first we need to cut this tie with this nut cutter.  so we will remove the tie and in second we will remove the wooden plate it's here so we need some screwdrivers and use the screws first  now we put aside the wooden plate and put the computing unit on the desk the next step we will take off  the connector plate on this both side. There's some more screws and we need to loosen first.  So we take out those connector plates. And the next step, we will remove the side plate.  the side plate is this front panel there are four screws  We need to lose first.  yeah so i think we should move the green connector power line first because it will stop the front panel so we need a new screw this flat and with a flat front  After you unscrew this you can just pull it. But you need to unscrew this a little more. Yeah. Yeah, I think I just cannot pull.  I believe it's at the maximum part. We should move this side first, right? But no, it's... There's another.  So this one was tight. Oh, there's another. Yep. So move the green connector first. So we will pull out the side panel. So the next step, we'll remove the top plate.  so we need first loosen the 6 screws  We still need to remove the bottom plate.  Next step, we'll remove the RAM, the RAM chip. It's here. We'll first pull this button and we can remove the memory chip. We'll pull it down here and detach the hardware power cable and the data cable.  So this is the hard disk. And we will remove the data and the power cable. So first this here.  and the power cable and remove the hard disk there are four screws here so we will remove these screws  oh yeah there are yeah there are eight  yeah so this is the last part and the connector cable and memory chip and plate and yep they're all set and the tools are here so we finish our disassemble task and yep  Where is my phone?"
    },
    {
        "category": "disassembly",
        "name": "User_17_414_2001_1_480.mp4",
        "transcript": " so today we are going to disassembly this task so first we need our gloves and some tools screwdrivers and keys so first we need to remove the task so we need to remove the screws here  And also this side.  and before we remove the desk we could use a marker to mark the position and the direction of this  So next time when someone assemblies the desk, they will know which direction and the right position. So now we will remove the desk.  and pull down the carpet so next step we need to disassembly this frame so first we need to crank so we can lower  the iron rod here connecting the two light two legs we will set to the lowest level  and remove the crank this time we will need allen keys here to remove the bolts first for the smaller ones it's too big  And don't let the lower plate fall.  and next step we have to remove the upper cover so we have to remove those bigger bolts  And the last one. Now we can remove the upper cover.  And.  we need an allen key for this one this one is too big  Yeah, this one suits.  And next step we need to prepare our drilling machines. I have to pull down the battery and find a suitable bit.  I'm going to use a smaller one. I think this one. Yep.  and this one so now we can separate these two lugs  and put it horizontal we still need to have to remove the base  so we need to remove these four bolts here with the allen key  and decide to remove these four bolts  and then I have to store these two sounds  so the allen keys and screwdrivers are here bolts are here and we have to remove the bed  and put back the drilling machines and take off the gloves so we finished the task"
    },
    {
        "category": "disassembly",
        "name": "User_17_414_2001_3_480.mp4",
        "transcript": " So today we're going to disassembly this desk. So first we need the tools and gloves. To disassembly the desk we need screwdrivers and some Allen keys.  So first we need to remove some screws here.  and also this side  so now we can remove the desk and we also need a blanket a carpet here on the floor so we can protect the desk and also we need a marker  in mark mark direction so we know we will know the right direction when someone assemblies the desk  so next step we have to disassembly this frame  So first, we need to use a crank to lower this frame.  Thank you."
    },
    {
        "category": "disassembly",
        "name": "User_17_451_2101_1_480.mp4",
        "transcript": " so today we are going to disassemble this trolley so first we need some tools and gloves we need some for the wheels this one and  yeah this allen key is for the different spools and bolts  so we will take these so first we will put on the gloves and first we need to remove this vertical bar  This.  so next step we have to remove this base plate this 3 base plate we need this allen key  and the middle plate  And the last one.  so now we remove the plate here the black plate here next we need to remove these four wheels so first flip it and we will need these  Where would be Alan Key?  And this side.  and we also have to move this small plate and we have to use the onion key again  so the last step we have to the last step we have to disassembly this frame so we first have to remove this middle bar and also these two bars  so we have to remove these connectors first and unscrew this bolt  And the last one.  so we now fully disassembly all the parts and we can now sort all the tools and parts together and put the tools back  and take off the gloves so the task is finished"
    },
    {
        "category": "disassembly",
        "name": "User_17_0710_480.mp4",
        "transcript": " This one?  yeah to be able to access it yep so you can just maybe uh loosen that a little bit and turn right or left because it's so hard oh yeah get it there  Sorry. Just keep it to the side of the camera. For the attached bar, position it like this. And I'm going to remove the two things here. For you, it's going to be on the other side. Yeah.  Thank you.  Can I use that? Yeah.  The other connection here.  oh it's really tight  I think the last piece here, this one, is attached with the help of this. So for this, you can maybe remove this gap first, but you can access this.  Or maybe you can just... It's not long enough.  Can I? Yeah, okay.  So the disassembly process is complete. So I just can't stop the recording. Complete."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_1_411_2210_3_480.mp4",
        "transcript": " We need a carpet. Okay. Okay.  So, we need to flip it. It's here? Switch.  it was somewhere  So I'll throw the trash. Oh, there's a switch. Laying on the door.  and the first thing that we are going to start off is with these handles yep, here are four this we need some alloy range no, it's too small too small? yep, it's a bigger one  yeah it fit so there are four no there's just two  put them together here next i think we should take this part or i think it should be let's check if you use this then you can  Yeah.  and this part too just detach the middle one  yeah and the last one is not very easy and the others because you ruin the structure and all the weights are pushing to the nails to the screws  I think you can just do the standing. I think you need to flip it and then flip it down. Where's the two inch? Yeah.  this one is a little bit too big perhaps we need missing 14 inch the other side  Yeah, Miss Dard claps.  It didn't lose it. It didn't remove it. Because start, collapse.  this can be a little bit hard to set them up to install, to assemble this I think we need to work on that  Once you hold this part. If it is 8000 to both then you can just flip it on. Yeah. Yeah. And.  Yep. Thanks for all.  so let's make sure that we have sorted the  and the table is there and these are for the fingers. No, there is no swirl symbol.  Yeah. Yeah."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_2_412_1510_1_480.mp4",
        "transcript": " So in order to disassemble this table, we need to remove those screws here. And the first thing we can do is flip it so we have better view and better angle to unscrew them. So we can use this.  Just place it on the ground. I think this is another. Yeah. So we first flip it. I'll hold. Do you have it?  yeah it's not so heavy on the bottom so maybe you can hold it and I unscrew it yeah it's not it's not heavy so we can both do this yeah there's one okay so I will hold it yeah  you  So I think now we can take off the whole clean. Yeah, maybe you can put them in your pockets. Yeah, okay. Into the pocket? Yeah, I have.  Yep. And the carpet? Yeah, okay. Yeah, it's not. Now, let's try this. It's okay? Yeah, it's okay. Now we can take the trolley. Yeah, okay. And then we can bring it to the conference room.  Should I take the phone? We may lost the Bluetooth connection. Weird.  then we just place it on top again  Is it in preposition?  Yeah. I mean, here is a line, but I don't see. Hmm.  On this side it's aligned. But here it's not. Here, here, here. Here, here. Yeah, I think that's it. Yeah. OK. So we'll put the scroll scene.  Yeah, just a chain.  Um, the electric. Yeah. Um, drill machine from next door. Because this one rotates. Like, maybe you can try, but it rotates together with the  Yeah. Yeah. Yeah. Yeah. Yeah. At the last part, it's just strange. We need a new machine. Yeah. Okay.  Here is the power socket. Plug in. Is that on? Yeah, that's right.  But first we also need to assemble it. Does this work? Yeah, it fits. I'll press this button to open it up. Insert the drill bit.  Press this button to tighten it. Hold onto the bike.  Now we can place it over here.  this one? we'll spray some on the table and a white waste paper  with a brand new paper. That's why I begin. Fold it.  and it's clean throw this paper to the garbage"
    },
    {
        "category": "disassembly",
        "name": "User_17_User_14_407_0601_1_480.mp4",
        "transcript": " And perhaps we should also need these. So we have to first move this. So we'll be using these tools, right? Yeah, yeah.  I wouldn't be smart.  so we will put it here this is the one and then we have to remove the plate  Bye.  and the wheels  Watch out for that.  Yeah.  These are two tiles.  and then I can do it.  You can press.  No, no, this one is... Two tights? Yeah, no, it's... Stop holding. Is it stuck?  Can you hold this? I'll hold the frame and press it.  Yeah. So, um, where do you put all this? Yeah. Oh, okay. And, um, yeah. You can use this one.  And you move that one? Yeah. Okay. We'll put it here. And then we have to remove these four. That's it. Yeah.  Where is it? That is a... I'll move that one.  yep so we can clean  And we can sort all the tools up. This is for the middle. Put the tools together.  Yeah. So take off the..."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_14_407_1712_1_480.mp4",
        "transcript": " And.  Let's do this. Yep.  Yeah, it's okay. Yep. Yep.  So, um, you can, we need, we need sensory and this one. Yep, this one.  Yeah, we can play here in order. And the screws. Where are the screws? You should put the screws in. No, we should put the screws together. Together? Yeah. Where are the screws? Yeah, just put it there.  Hmm. Yep.  You can use this one. This is quicker. Much faster.  So, this is the middle one. Yeah, just put it here. No, you don't have to insert it. Can you give me that one? Yeah, you can use this one.  You can remove the others.  Can you hold this one? Yeah, you should put it there. No, no. You put it here. Lean water. Yeah, you can.  so we stored all the tools together the tools we need is here and we can clean all the plates put here this for the  Yeah, sorry. I will spray it on it and you can clean it.  Yeah, so I think, yeah, screws are here. Yeah.  And we can put it on the desk. Yeah, I think that's it. That's what we can do for the assembly. So the class, yeah."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_14_411_2810_1_480.mp4",
        "transcript": " So first we need this. Yep. And we need to. Yep, here.  Yeah, we need a cross. We need a cross. Screwdrivers here. This one? Yeah, that's right.  No, that doesn't fit.  Yeah, this bit, this bit. No, we have to pull the gloves. Don't cut your hand. Yeah, so mine's here. Where's the gloves? Here.  Or this one?  Yeah, it's working. So we'll put the screws together. And the other one. Okay. There's one here. I can see it.  So we have to mark the front side. And the pin. Yep. Mark. Yeah.  so we will remember the front side and move this so we should also mark on the other side yeah it's okay yeah it's okay we can see from the one side and let's put this let's take it off okay and where put where  Yeah, but there's some... We have to remove these tools. The tools? Yeah, okay. No, it's fixed. It fixed. Yeah. Let's take with the glues. With tapes, double tapes.  and we have to move we need to we need to assemble it all yeah  This one needs some intercept.  Can you also underscore this one? Yeah, I'm trying. I'm trying. The small one? Yeah. This one? How did you remove these screws? Like, with what?  Yeah, the upper one is with this, with the bigger one, you know, you have to... So where do you put the small one? Yep, that's it.  Yeah, yeah.  So is everyone here? Is everyone here? There's two kinds of schools.  Watch your fingers. And this one to the side.  So we need to use the training machines too. Let me check. So for removing these, you can use a training machine.  Yeah. These two, right?  Oh, this is a... Hmm.  Let's try it first. I don't think it's the right one. No, it's too small. That's not the right bit. And there's no other bit. This one?  Watch out.  No. Still. No. We tried all this for...  There's four of them, but they're all too small for the screen. There's not much left to choose.  No. No. Doesn't fit? Yeah. These are too small. Yeah. No, that's not. Mmm.  Is there any other? That's a fix.  That one? No. It doesn't fit. Yeah. Or... No. Still, it's too small. No, it doesn't... It doesn't fit. Yeah. You can find a suit. A suit will fit.  Um, is your...  Let's try these. These two. Did you also try this one? Yeah. This one looks better. Yeah, but still it doesn't. Okay.  No. Or the screw probably. Let's try the other side. Perhaps the screw is  The surface is kinda damaged. Yeah, I know, I know. It's not this frost. It's something with six.  Which one? This one? It's a cross. It's not a cross. It should be... Like... Yeah, like a star. Yeah, that should be a star or something like that. It's small. It's still small.  Is there any big star? This one probably too big. Probably we need someone in the middle. This one, so let's first try this one. Let's try these two.  Yeah. The wrong side, the wrong direction. Really? But it's not coming out. Is it moving? Yeah, it's moving, it's moving.  take this out and don't need this anymore and yeah that's one and these two  Watch it, watch it. Yeah, that's the one. So yeah, we...  finish this part and still this part right that's the last one so is there any part we have to remove and let's just turn it to your side  yeah yeah so the tools so we have to move place some tools on the desk and the schools yeah here these tools this one yeah now to put the tools together and  There's some cross, stars, there's some symbols there. If there, you can find no place. Yeah, no, just put it in.  Yeah, okay. Take off the glass. So you can stop."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_14_411_3010_1_480.mp4",
        "transcript": " Yeah, it's starting. So first, you can go to Pubs. I hope you use this one.  So that's our tools and we first pull it. Pull the frame, the base part. Yep, yep. Yep. Just pull it a little bit out. Yeah, yeah, here, yeah, okay. And we first we have to, yep. Take this. Yep, it's very simple.  and we can remove these two first  These two. Within the bottom? Yeah, down.  yeah don't really tie it loosen so it will collapse yeah we can flip it over and yeah  another one so we can place them together and then we can first turn it over  And we can first remove these two rows.  um with allen keys there there are two scrolls you know here yep there are two scrolls and there are two scrolls there are two first remove this one these rules and we can move this one yeah so  Oh, that's a bit dangerous. We have to, we don't have, yeah. And there's actually, I mean, no, not this one. And you can remove that screw, and I can remove this one. So we can hold it, so it doesn't really fall from hyper.  Yep, yep, I'm holding. Is this the same? Yeah, okay, so we place it.  Yep, so that's for the allen keys and we have to reuse the wrench. Yeah, okay. You put somewhere. Okay. Yep, so I will remove these two and you can remove that.  Yeah, okay, okay. Yeah, just don't take it out. You just lose a bit. That's enough.  Yep. Did you lose it? Yeah, I'm losing it, but it's not coming out. Yeah, whatever. You can lose that one.  Yeah, when you lose it, actually you can just use your screws, use your hand screw a bit and it will come out. And watch your fingers.  Yeah. Or you can use this wrench. Which one? This one. Mine. You don't need... Ah, okay. Yeah, that's fine. Wow, wow. Watch your hand. Yep.  And you place it aside. They're actually... Yeah, you can use your hand to turn it. No.  Yep. Can you remove it? Yeah, okay. Yep. So we have these two. And these two. We can place them together. Yeah. And the screws. Yep. These two.  there is actually an order for this for the legs so is it done? yeah and we can place two together"
    },
    {
        "category": "disassembly",
        "name": "User_17_User_15_410_2210_1_480.mp4",
        "transcript": " Yeah, thank you. So today we're going to... And the first step is pull down the gloves.  Maybe you go on this side and I do this side. So this is two. Yeah, so those two and those two here. Ah, yeah, I see. If you go on this side. Yeah, okay.  We have to pack them together, put them together.  The next step is remove the crank. It's already removed.  oh someone yeah yeah i get them and so we can yep this too  What does it say on that? Yeah, it's removed about holding the two end of the connecting road from the inside. Yeah, it's here. No, it doesn't fix. Yeah, is that right? Yes.  Okay.  So it's up here. That was the wrong direction. It's still the wrong direction. I don't know. It's just in the main. No. It's because I have to turn this over to the screw. Yeah. It's doing now, right?  Maybe this makes a difference. It's not... Yeah, yeah. Yeah, it's right. It's doing all right. Yeah, this time it's right. Okay, there's one.  Why is it not working? Watch out your finger. I don't understand why it's not working. Yeah, perhaps we can try in the... Perhaps there's some... We can try this side and see...  Just turn back in.  Is it fixed? It's fixed. I'm just jammed here.  Yeah. Did you get it? No, it's not working and we can do it perhaps manually.  Is there a screwdriver? Yeah, I would just use this. If you can.  Can't find one. Ooh.  no let's do just try it with different just you don't use really hard force no yeah it's a screw mode yeah  Is it working? Is it working?  It's like using the horse to use the horse to pull a car. Move in the middle.  Yeah. Yeah. Okay. Lay it down. Yeah. So it's on here. There's a big one.  Thanks.  So where's the last part? It's here. Make sure that the buttons are scattered and separate from the others. Put the tools back. Detach the drills and remove the gloves and that's the disassembler part. To stop the recording.  Is it recording? Oh yeah. Yeah. First form."
    },
    {
        "category": "disassembly",
        "name": "User_17_User_16_410_1410_2_480.mp4",
        "transcript": " Yeah.  This one? Open the door.  Watch out. It's too long. Yeah, it fits. Yeah. Go to here.  Yes, put it on the ground.  I'm going to disable this to remove the screws. Smaller size and bigger size. One, two, three, four. Each slide. So, on the screwdriver, I will  Yeah, this one. Yeah, fit. And where should I pull the screws?  here.  which part? this one? no there is one here we need to remove this too  Should we remove this part?  this part. No, it doesn't fit.  Yeah, this.  No, this one is a little bit small. I'll try this one. No, it's big.  And there's 0.2. There's 0.2.  Yeah, this part is from the downside. There's still one.  Put it on the desk here. Lift it up. It's out. Here.  can we lift it up? can we lift it up? it's four?  Thank you.  Here is one more screw. So the screw is out. How can we just move it? Okay. So for this part, oh, there is still... Okay.  Can we get out? There is two more, I don't see. You can see? This is fixing the stick here. So without lag. So we can do some of this part. Give it a try.  Or just move this stick out. Is this movable? No. If we want to remove this part, we have to move this to... Yeah, perhaps this is a long scroll from this side to this side.  We have to move it first. Remove it. No, it's not a right tool. It's not a problem. I think we need this screwdriver. No, it doesn't fit.  There is another screwdriver but this didn't fit neither so we need a new screwdriver. A smaller one or bigger one? A bigger one.  What do you have here?  Sorry.  Yeah, we need a new screwdriver. So this is the power line. I'm trying to find which one fits the star shape.  and i will try to get this so wait here oh okay  There's a screw from here, from the bottom.  here no no we need to yeah there's still two more here  No, we can't. We have to move the stick out first. Can you hold it? Thank you. I'll lose this one. With my hand. I'll lose the last part. Thank you. And also.  So we still cannot pull it out. No, still not. This little black part can be moved a little bit.  Oh, we can pull it apart now, here. Can you? Oh, no. No, it's from inside. But we can still pull it. Yeah, yeah. Yeah, OK. No, there's some oil. It's not oil. I think it's mesh. It's a metal mesh.  You can just pull it out like this. No, there's some stock inside.  ah remove it this part moves you have to lose this part first  Thank you.  use this it can automatically connect it to the height it can move together so if we move this part it's connected to the old leg you can see yeah but i don't have a part like this here because a they are moving together so it's the same direction now we're down to the lowest  Okay, because it's too hard, you need a long hand."
    }
]